← Blogs
The GYEON Car Care Book cover

GYEON · Car care knowledge · Edition 2026

The GYEON Car Care Book

109 expert guides – from the first wash to lasting protection

Washing, decontamination, polishing, protection, wheels, glass, interior and PPF care.

GYEON · Innovative Chemicals
Content based on the GYEON e-shop knowledge base. Photography: GYEON HUB.

Always read the product label and technical data sheet before use, and test any product on a small, inconspicuous area first. Product names, dilutions and durability figures reflect the GYEON range at the time of writing.

GYEON car care

Foreword

Quality is not an act. It is a habit.

Every car tells a story about the person who looks after it. Some of those stories are written in a single weekend of polishing; most are written wash after wash, season after season, in small habits done properly.

This book collects what we have learned into 109 practical guides. It follows the way a car is actually cared for: you start with the right kit, you wash safely, you remove what washing cannot, you correct the paint, and only then do you protect it – before moving on to wheels, glass, the interior and paint protection film.

Each guide is built the same way. In short gives you the answer in a few lines. What you need lists the products and tools. Step by step walks you through the job, and the GYEON tip is the one thing our trainers wish everyone knew.

You do not need to read it cover to cover. Open it when a bird has visited your bonnet, when your coating stops beading, when winter is over, or when you have just picked up a new car. Use the contents, the chapter openers or the product index at the back to jump straight to what you need.

Whether you are washing your first car or running a detailing studio, we hope this book helps you protect what you love – and enjoy the process as much as the result.

The GYEON Team
In G we trust.

How to use this book

The GYEON method

Car care works best in a fixed order. Never protect a surface you have not cleaned, and never polish a surface you have not decontaminated. The chapters of this book follow the same logic.

  1. PrepareRight kit, right towels, a plan.Chapter 01 →
  2. WashpH-neutral, two buckets, safe drying.Chapter 02 →
  3. DecontaminateIron, tar, minerals, clay.Chapter 03 →
  4. CorrectPolish out swirls and scratches.Chapter 04 →
  5. ProtectCoating, sealant, wax or film.Chapter 05 →
  6. MaintainRegular washes and toppers.Chapter 02 →

How to read a guide

Chapter & type
Complete guide – the full process. Knowledge – how and why. Real-life fix – a specific problem solved. Product guide – choosing between GYEON products.
In short
The answer, before the detail.
What you need
Products and tools for the job. GYEON products are listed in the product index.
Step by step
The sequence that gives the best and safest result.
GYEON tip
The detail that makes the difference.
Read next
Related guides with links to their sections.
Chapter 01

Start here

Every great finish starts with the right kit and a simple plan. This chapter covers what to buy first, which towels and tools you really need, how your paint is built and how often each job should be done.

Start here
Product guide #

Your first GYEON kit: what to buy to start

Seven products cover 90% of what you need. Here's where to start.

Starting out in car care? You don't need every bottle on the shelf. A small, well-chosen kit lets you wash safely, keep your wheels clean and add protection – and you can build from there.

In short

Start with Q²M Foam, Q²M Bathe, Q²M Iron WheelCleaner REDEFINED, Q²M WetCoat, a Q²M Smoothie EVO wash mitt and a Q²M SilkDryer EVO drying towel, plus two buckets. Add Q²M Bug&Grime in summer and an interior cleaner when you're ready.

In detail

STEP 1 – THE ESSENTIALS (EVERY WASH)
STEP 2 – NEXT ADDITIONS
STEP 3 – WHEN YOU'RE READY FOR MORE

How to choose

  1. Wheels first with Q²M Iron WheelCleaner REDEFINED.
  2. Pre-wash with Q²M Foam, rinse.
  3. Two-bucket wash with Q²M Bathe and Q²M Smoothie EVO.
  4. Spray Q²M WetCoat on the wet car, rinse.
  5. Dry with Q²M SilkDryer EVO.

GYEON tip

Not sure which products you'll like? The Q²M Experience Set (9 × 80 ml) lets you try a range of products first.

Back to contents ↑
Knowledge #

Essential tools for DIY car detailing

The right tools make detailing safer, faster and more fun. Here is the essential kit.

Detailing at home? The right tools save time, protect your car – and protect you.

In short

Invest in a good pressure washer, labelled buckets, safety gear, a dedicated vacuum, premium microfibres and mitts, a floor jack with axle stands, a good inspection light and something comfortable to sit or kneel on.

The background

5 golden rules:
  • Always wash in the shade
  • Make sure the car is cool
  • Always start with a non-contact pre-wash
  • Never reintroduce dirt into your wash
  • Don't get distracted and leave products on too long

What you need

Premium microfibres and wash mitts Q²M Smoothie , Q²M SilkDryer , Q²M BaldWipe

Pressure washer with quick-release fittings and a long hose

Buckets labelled 'wheels', 'wash', 'rinse' (translucent ones show how dirty the water is)

Nitrile gloves, ear defenders, a face mask with changeable filters

A vacuum with automotive attachments

Floor jack and axle stands

Inspection light

Rolling stool and kneel pads

Step by step

  1. Pressure washer: buy the best you can afford – cheap ones don't last. Quick-release fittings make switching to a foam cannon easy.
  2. Buckets: one per task, labelled, to avoid reintroducing dirt.
  3. Safety: products can irritate skin, machines damage hearing and polish dust harms your lungs.
  4. Vacuum: a household upright lacks suction, hose length and attachments.
  5. Quality fabrics: premium towels and mitts reduce scratching and last longer.
  6. Floor jack: remove wheels to clean arches and barrels properly – always with axle stands.
  7. Inspection light: essential when polishing.
  8. Comfort: a rolling stool and kneel pads make the lower sections much easier.

GYEON tip

Translucent buckets show you exactly when it's time to change the water.

Back to contents ↑
Product guide #

Which GYEON towel for which job?

Twenty towels, one simple chart.

Using the right towel makes every job easier – and safer for your paint. Here's the GYEON microfibre range, job by job.

In short

Drying: SilkDryer EVO (or Ultra, SoftDryer, WaffleDryer). Washing: Smoothie EVO, WashPad EVO, WheelMitt EVO. Coatings and sealants: BaldWipe EVO, PolishWipe EVO, SoftWipe EVO, Suede EVO. Glass: GlassWipe EVO. Interior: InteriorWipe EVO and LeatherWipe EVO.

In detail

DRYING
  • Q²M SilkDryer EVO – twist-loop, 530 GSM; 40×60, 50×55 or 70×90 cm. Streak-free drying.
  • Q²M SilkDryer Ultra EVO – double-sided, 1040 GSM, 40×60 cm. Compact and very absorbent.
  • Q²M SoftDryer EVO – plush, 60×80 cm; an alternative to waffle towels.
  • Q²M WaffleDryer EVO – classic waffle, 390 GSM; paint, trim, rims and glass.
  • Q²M SilkMitt EVO – drying hard-to-reach areas; also for tar and sap removal during decontamination.
WASHING
COATINGS, POLISHING AND SEALANTS
  • Q²M BaldWipe EVO – low pile all-rounder: cleaning, polish removal, first coating wipe.
  • Q²M PolishWipe EVO – double-sided 310 GSM: polish oil removal and paint inspection; also for wax removal.
  • Q²M SoftWipe EVO – plush and thick: wiping coatings, quick detailers and spray sealants.
  • Q²M Suede EVO – ultra-short pile: coating wipe-off and glass coating mist removal.
  • Q²M MF Applicator EVO – applying coatings, sealants, trim and leather products.
GLASS AND INTERIOR

What you need

Q²M TowelWash to wash them

See the list above

How to choose

  1. Pick one drying towel and one wash mitt.
  2. Add BaldWipe EVO and SoftWipe EVO if you use sprays or coatings.
  3. Add GlassWipe EVO for glass and the InteriorPack EVO for the cabin.
  4. Keep towels separated by job, and wash them with Q²M TowelWash.

GYEON tip

Use different colours for different jobs – you'll never use a wheel towel on paint by mistake.

Back to contents ↑
Complete guide #

Microfibre towels: choosing, using and washing them

Microfibre towels: choosing, using and washing them

Your towels touch your paint more than anything else. Choose them well and look after them.

Microfibre towels are among the most important tools in detailing – they touch your paint more than anything else. Choosing the right ones and washing them correctly makes a real difference.

In short

Use high-quality, edgeless towels that are safe on soft paint, keep a dedicated towel for each job, wash them separately at max. 30 °C with Q²M TowelWash and no fabric softener, and let them air dry.

Guide

1. WHY PREMIUM TOWELS MATTER

Not all paint is the same – some is very soft. High-quality towels are safe on soft paint, durable and make every job easier. All GYEON towels are laser-cut and edgeless, so there's no hard edge to mark the paint. Cheap towels are false economy: they wear out faster and can scratch.

2. THE RIGHT TOWEL FOR THE JOB

Keep separate towels for paint, glass, wheels and interior.

3. HOW TO WASH THEM
  • Separate dirty-work towels (wheels, engine bay, heavy grime) from the rest.
  • Never wash microfibres with other fabrics.
  • Cold or warm water – never above 30 °C – on a normal cycle.
  • Use Q²M TowelWash, or a detergent without conditioner or fabric softener (they clog the fibres).
  • Air dry. Tumble dryer only without heat.
  • Very dirty towels: pre-soak 30–60 minutes in warm water with Q²M APC diluted 1:15.
4. WHEN TO RETIRE A TOWEL

Towels used to apply coatings are never safe for paint again, even after washing – keep them for dirty work. Same for towels that feel stiff or have picked up grit.

GYEON tip

Colour-code your towels by job – it's the easiest way to never use a wheel towel on paint.

Back to contents ↑
Knowledge #

5 ways to maintain your detailing equipment

5 ways to maintain your detailing equipment

Your kit looks after your car. Here's how to look after your kit.

Detailing equipment is an investment. A few habits keep it working – and stop it putting dirt back on your car.

In short

Wash your mitts and towels, drain your pressure washer hose, flush your shampoo vac, clean your buckets and blow the dust out of your polishers.

What you need

A soft brush and vacuum or airline

Step by step

  1. Wash mitts and towels regularly – clogged with dirt or product, they perform worse and can scratch.
  2. Drain the water from your pressure washer hose after use – it prevents corrosion inside the hose.
  3. Flush your shampoo vac after every use, with Q²M APC on stubborn areas – otherwise it smells and moisture builds up.
  4. Clean your buckets – dirt left in them ends up back on your paint.
  5. Blow or vacuum dust from your polishers' vents and backing plate with a soft brush after each day of polishing.

GYEON tip

Don't wrap the power cord tightly around your polisher – it can break the inner cable.

Back to contents ↑
Complete guide #

Car paint explained: layers, finishes and common defects

Car paint explained: layers, finishes and common defects

Understanding your paint is the first step to caring for it. Layers, finishes, gloss and the defects you'll meet.

When you wash, polish or coat your car, you work on one thin layer of a complex paint system. Knowing how it's built – and how it gets damaged – helps you choose the right care.

In short

Car paint has three layers – primer, base coat and clear coat. Almost all care happens on the clear coat. Defects are either mechanical (swirls, marring, scratches) or environmental (bird droppings, water spots, tar, fallout). Gloss is how much light the paint reflects – defects scatter it.

Guide

1. THE THREE LAYERS
  • Primer – gives the panel a uniform base.
  • Base coat – gives the colour.
  • Clear coat (lacquer) – the final layer, usually high-gloss but also matte or satin. It protects the colour from oxidation and UV damage.

Every polish removes a little clear coat – so protect first, polish only when necessary.

2. PAINT FINISHES THROUGH TIME

From varnish in the late 1800s, nitrocellulose (1920s), acrylic enamels (1930s – polished with cornstarch!) and acrylic lacquers (1950s), to urethane clear coats and, from the 1990s, almost universal base-and-clear systems. Today: water-based colour, tinted clears, matte, satin, self-healing and UHS clears. And some modern paints are still extremely soft – always know your paint before polishing.

3. WHAT IS GLOSS?

Gloss is how much light is reflected off the paint, measured at defined angles with a gloss meter. The two industry standards are RIQ (Reflective Image Quality) and DOI (Distinctness of Image). Swirls and scratches scatter light instead of reflecting it – that's why corrected paint looks glossier.

4. MECHANICAL DEFECTS
  • Random deep scratches – defects of use that cut deep into the paint.
  • Holograms and buffer trails – wavy lines from polishing, visible in direct light.
  • Micro marring – often after the cutting stage with a DA; needs refining.
  • Marring – straight-line defects, often after claying; usually removed with a one-step polish.
  • Swirls – spider-web scratches, mostly from wrong washing.
  • Paint scuff – paint transferred from another surface; light scuffs usually polish out.
5. ENVIRONMENTAL DEFECTS

Acid rain, bird droppings and etching, corrosion, industrial fallout, bug splatter, tar spots, tree sap and water spots.

6. A SMALL HABIT THAT CAUSES BIG DEFECTS

Drawing 'wash me' in the dust – or leaning against a dirty car – drags abrasive road dirt across the clear coat and mars it. Same for wiping a dry, dusty car with a cloth.

What you need

Q²M Iron , Q²M Tar , Q²M Bug&Grime environmental contamination

Q²M Bathe , Q²M Smoothie , Q²M Foam safe washing

Q²M WaterSpot water spots

GYEON polishing compounds and pads ( Q²M Compound , Compound+ REDEFINED, Polish, Q² Primer ; Q²M Heavy Cut , Cut, Polish, Finish pads) mechanical defects

Q² CanCoat EVO protection

GYEON tip

Prevention beats correction: most swirls come from washing, not from driving.

Back to contents ↑
Product guide #

Safe on PPF, matte paint or a coating? GYEON product compatibility

Before you buy: will it work on your car's finish? A quick reference.

Coated paint, PPF, matte paint and wraps each need a little care in product choice. Here's what GYEON says about its main products.

In short

Most GYEON maintenance products are safe on ceramic coatings. For matte finishes, use the dedicated matte products (Q² Matte EVO, Q²M Cure Matte REDEFINED). For PPF and wraps, Q²M PPF Wash, Q²M PPF Maintain REDEFINED and Q² PPF EVO are made for film. When in doubt, test on a small area.

In detail

ON CERAMIC COATINGS – STATED AS SAFE

Q²M Bathe, Q²M Bathe+, Q²M EcoWash, Q²M PPF Wash, Q²M RestartWash REDEFINED (made for coatings), Q²M WetCoat, Q²M CeramicDetailer, Q²M Cure REDEFINED, Q²M QuickDetailer, Q²M Iron WheelCleaner REDEFINED (coated wheels), Q²M Glass+ (coated glass), Q² Wax (as a top coat on a cured coating), Q²M Bug&Grime.

ON MATTE PAINT, MATTE PPF AND WRAPS
ON PPF AND WRAPS
WATCH OUT
  • Q²M RestartWash REDEFINED is acidic: it may affect some waxes and sealants – test first.
  • Q² CanCoat EVO on glass: side and rear windows only.
  • Q² Rim EVO on calipers: only if clear-coated.

How to choose

  1. Identify your finish: gloss paint, matte paint, PPF, wrap, coated or not.
  2. Check the list above.
  3. Not listed? Check the product page FAQ, or test on a small, hidden area first.

GYEON tip

Matte car? Never polish or clay it – the finish can't be corrected without changing its look.

Back to contents ↑
Product guide #

Your car care calendar: weekly, monthly, quarterly and seasonal

Little and often. Here's what to do – and when.

Most car care problems come from doing too much too rarely. A simple calendar keeps your car clean, protected and easy to maintain all year.

In short

Every 1–2 weeks: safe wash and a booster. Monthly: interior wipe-down, glass top-up, tyre dressing. Every 3 months: chemical decontamination. Spring and autumn: a deeper session and fresh protection.

In detail

EVERY WASH (EVERY 1–2 WEEKS OR 2,000 KM)
EVERY MONTH
EVERY 3 MONTHS
SPRING
AUTUMN
  • Protect before the bad weather: paint, trim, wheels.
  • Q² AntiFog on the inside of the glass.
  • Protect leather and fabric against wet, dirty clothes.
EVERY 1–4 YEARS
  • Re-coat, depending on your coating (see How long does it last?).

How to choose

  1. Print or save the calendar.
  2. Set reminders for monthly and quarterly tasks.
  3. Adjust to your climate and how much you drive.

GYEON tip

Harsh conditions (salt, sap, bird droppings) mean washing more often – never less.

Back to contents ↑
Real-life fix #

Just bought a used car? 5 things to do first

Make it yours: remove every trace of the previous owner and find out what you really bought.

A new-to-you car deserves a fresh start – and a proper clean shows you what you really bought.

In short

Deep clean the interior and contact points, clean the seats, clean the interior glass, hot-wash the paint with a degreaser to reveal its true condition, then choose your protection.

What you need

Q²M FabricCleaner or Q²M LeatherCleaner seats

Q²M InteriorDetailer contact points

Q²M Glass interior glass

Q² Wax or Q²M WetCoat short-term protection

Q²M TotalRemover degreasing wash

Q² CanCoat EVO long-term protection

Step by step

  1. Deep clean the interior – remove all dirt left by the previous owner. Wipe every contact point (handles, steering wheel, gear stick) with Q²M InteriorDetailer.
  2. Clean the seats – fabric or leather.
  3. Clean the interior glass: nicotine film, sticky fingerprints, pet grime. Better visibility and safety too.
  4. Hot wash with a good degreaser to reveal the paint's true condition and spot areas that need correction.
  5. Choose protection: short-term (Q² Wax, Q²M WetCoat) or long-term (full decontamination, correction and a coating or PPF).

GYEON tip

Step 4 is an eye-opener: fillers and old wax can hide defects that a degreasing wash reveals.

Back to contents ↑
Chapter 02

Washing

Most swirls are put into paint during washing. Get the routine right – the shampoo, the pre-wash, the contact wash and the drying – and everything else becomes easier.

Washing
Product guide #

Bathe, Bathe+, RestartWash, EcoWash or PPF Wash: which GYEON shampoo do you need?

Five shampoos, five different jobs. Here's which one fits your car and your routine.

GYEON makes five car shampoos – and they don't do the same thing. Choosing the right one depends on your car's protection, how dirty it is and where you wash.

In short

Q²M Bathe is the everyday pH-neutral shampoo for any car. Q²M Bathe+ adds SiO₂ protection while you wash. Q²M RestartWash REDEFINED is an acidic decontamination wash for coated cars that have lost their beading. Q²M EcoWash cleans without running water. Q²M PPF Wash is made for film and wraps.

In detail

Q²M BATHE – THE EVERYDAY SHAMPOO
  • Highly concentrated, pH-neutral (pH 6) – safe on coatings, sealants and delicate finishes.
  • Very slick: reduces wash-induced defects.
  • Dilution 1:500 – about 15–20 ml per car.
  • Choose it if: you want one shampoo for every regular wash, coated or not.
Q²M BATHE+ – WASH AND PROTECT
  • pH-neutral shampoo with SiO₂ – adds instant hydrophobicity and self-cleaning while you wash.
  • Real-world lifespan up to 8 weeks.
  • Dilution 1:500; use it in a bucket, directly on the mitt, or in a foam cannon.
  • Safe on paint, rims, glass and plastics, coated or bare.
  • Choose it if: you want to boost or maintain protection without an extra step. Not a coating replacement.
Q²M RESTARTWASH REDEFINED – DECONTAMINATION WASH FOR COATED CARS
  • Acidic (pH 4 concentrate): removes mineral and ferrous contamination – water spots, limescale, iron particles – in one wash.
  • Restores the coating's water behaviour and slickness. Adds no protection of its own and doesn't mask anything.
  • Dilution 1:500 (light), 1:250 (standard), 1:100 (intensive).
  • Choose it if: your coated car has lost its beading. For routine washes, use Bathe.
  • Note: can affect some waxes and sealants – test first. Rinse well; never let it dry.
Q²M ECOWASH – NO RUNNING WATER NEEDED
  • Waterless (1:10–1:15), rinseless (1:150–1:256) or drying aid (1:20).
  • SiO₂-enriched for slickness and light water repellency; safe on coated and uncoated cars.
  • Choose it if: you live in an apartment, washing with a hose isn't allowed, or the car is only lightly dusty.
Q²M PPF WASH – FOR FILM AND WRAPS
  • Decontamination shampoo that dissolves mild iron contamination on PPF and vinyl without claying.
  • Coating-safe, safe on all exterior surfaces. Dilution 1:500.
  • Choose it if: your car is (partly) wrapped in PPF or vinyl.

What you need

Q²M RestartWash REDEFINED decontamination for coated cars

Q²M Bathe everyday

Q²M Bathe+ wash and protect

Q²M EcoWash waterless/rinseless

Q²M PPF Wash film and wraps

How to choose

Quick chooser:
  1. Normal weekly wash, any car → Q²M Bathe.
  2. Want more beading without an extra step → Q²M Bathe+ (every other wash, or all the time).
  3. Coated car not beading like before → Q²M RestartWash REDEFINED, then back to Bathe.
  4. No hose or only light dust → Q²M EcoWash.
  5. PPF or wrap → Q²M PPF Wash.

GYEON tip

Many owners keep two: Bathe (or Bathe+) for every wash and RestartWash REDEFINED every month or two on a coated car.

Back to contents ↑
Knowledge #

Must-have products for washing your car

Starting from scratch? This is the kit that covers every wash.

Starting your car care kit – or wondering what you're missing? These are the essentials for washing and maintaining any car.

In short

Q²M Foam (pre-wash), Q²M Bathe (shampoo), Q²M Bug&Grime (stubborn contamination), Q²M IronWheelCleaner (wheels), Q²M WetCoat (protection), Q²M Smoothie (wash mitt) and Q²M SilkDryer (drying towel).

What you need

Q²M Bathe everyday shampoo, safe on coated cars and PPF

Q²M Bug&Grime bug splatter, tree sap, bird droppings

Q²M Foam pre-wash

Q²M WetCoat hydrophobic layer after washing, keeps the car cleaner for longer

Q²M IronWheelCleaner brake dust and grime on wheels

Q²M Smoothie wash mitt

Q²M SilkDryer drying towel

Q²M LeatherCleaner – if you have leather seats

Step by step

  1. Pre-wash with Q²M Foam (and Q²M Bug&Grime where needed).
  2. Clean the wheels with Q²M IronWheelCleaner.
  3. Wash with Q²M Bathe and Q²M Smoothie.
  4. Spray Q²M WetCoat on the wet car and rinse.
  5. Dry with Q²M SilkDryer.

GYEON tip

Have leather seats? Add Q²M LeatherCleaner – it removes grime and oils without damaging the leather.

Back to contents ↑
Complete guide #

Pre-wash and touchless cleaning explained

Pre-wash and touchless cleaning explained

The less dirt on the car when your mitt touches it, the fewer scratches. Here's how to get there – without touching the paint.

Pre-wash is a non-contact stage designed to remove as much dirt and contamination as possible in the safest way – so there's less to drag across the paint once the contact wash begins.

In short

Clean wheels and door shuts first, soak lower panels with Q²M APC, cover the car in Q²M Foam, let it dwell without drying and rinse thoroughly. A touchless wash alone never removes 100% of the dirt – it prepares for a safe contact wash.

Guide

1. WHAT IS TRAFFIC FILM?

Traffic film is the build-up of road grime on your bodywork and chassis – dirt, oils, salts and contamination. It varies by climate and road type, and so do the products that remove it, from alkaline to acidic, at different strengths. Every pre-wash is designed to cut through this film before you wash.

2. THE PRE-WASH, STEP BY STEP
  • Make sure the car is fully cooled down.
  • Wheels first – remove them if you can, which also gives access to the inner arches.
  • Door shuts before the paint, so their dirt doesn't run onto clean panels: spray Q²M Bug&Grime or Q²M APC (no overspray inside!), agitate with a Q²M Bathe solution and a dedicated mitt, rinse and finish with Q²M WetCoat.
  • Spray Q²M Bug&Grime on bugs and heavy road film.
  • Soak the lower sections with Q²M APC, working from the ground up for an even dwell time.
  • Snow foam the car with Q²M Foam (1:5 to 1:15), bottom to top. Let it dwell 3–4 minutes – never let it dry.
  • Rinse thoroughly and check the car is free of loose dirt before your contact wash.

Very dirty car? Add a little Q²M APC to your snow foam solution.

3. TOUCHLESS WASHING: PROS AND LIMITS

Touchless – or chemical – washing cleans at a chemical level: the solution reacts with the dirt and both are rinsed off with water. Snow foams, fallout removers and traffic film removers all work this way.

It's popular with people who fear wash marks. But:
  • It never removes 100% of the dirt.
  • Harsh chemicals at self-service or automatic touchless washes, used repeatedly, can damage your protection and sensitive trim or wheel finishes.

The best approach: a touchless pre-wash to remove most of the dirt, followed by a safe contact wash.

4. FOR THE EFFICIENCY-MINDED: PIR

Panel Impact Ratio (PIR) is a method to calculate exactly how much product lands on your car during the pre-wash. It's not for everyone – but if you want to know how efficient your pre-wash really is, it gives you the numbers. Following the recommended dilutions on the label is always the best starting point.

What you need

Q²M Foam snow foam

Q²M Bathe and Q²M WetCoat door shuts

Q²M IronWheelCleaner wheels

Pressure washer and foam lance

GYEON tip

Never let foam or pre-wash products dry on the paint – work in the shade and rinse in time.

Back to contents ↑
Complete guide #

The complete car wash routine: step by step

The complete car wash routine: step by step

Most swirl marks are made during the wash. This is the routine that keeps your paint flawless – from the wheels to the last drop.

Most swirl marks are not made on the road – they are made during the wash. The good news: a safe routine doesn't take longer than a bad one. It is simply about doing things in the right order, with the right tools.

In short

Wash a cool car in the shade. Start with the wheels, pre-wash to remove loose dirt, wash with two buckets from top to bottom, rinse thoroughly and dry with a plush towel without pressure. Every 3 months, add a chemical decontamination.

Guide

1. BEFORE YOU START

Wash in the shade, early morning or evening, and make sure paint and wheels are cool to the touch. On hot panels, water and products dry too fast and leave spots.

Warm water helps your shampoo work better – but avoid very hot water on a waxed car, as it can soften the wax. Always check the product label: some formulas depend on temperature.

2. WHEELS FIRST – AND WHY

Start with the dirtiest, most time-consuming areas: wheels and wheel arches. If you leave them to the end, products dry on the car and water spots form on paint and glass.

Don't rinse the whole car before the wheels – cleaning four wheels takes about 30 minutes, and water sitting on the paint all that time leaves spots. Work on one wheel at a time. (Full guide: How to wash your wheels.)

3. PRE-WASH

Remove as much dirt as possible before you touch the paint: Q²M Bug&Grime on bugs and road film, Q²M Foam (1:5 to 1:15 in a foam lance) over the whole car, 3–4 minutes dwell, never let it dry, then rinse. (Full guide: Pre-wash and touchless cleaning explained.)

4. THE 2-BUCKET WASH

Why two buckets? The dirt you remove ends up in your mitt. Without a rinse bucket, it goes straight back onto the next panel – causing swirls, scratches and marring.

  • Fill both buckets with 10 L of water, each with a grit guard. Add Q²M Bathe at 1:500 (about 20 ml) to one bucket and foam it up; the other is your rinse bucket.
  • Soak the Q²M Smoothie in the rinse bucket first, then load it with shampoo. Wash top to bottom in straight, side-to-side lines – never up and down, so you don't drag dirt up from the lower panels.
  • After each panel, dunk the mitt in the rinse bucket and rub it on the grit guard, then reload. Once the mitt has touched the lower part of a panel, never go back up with it.
5. RINSE PROPERLY

It is tempting to stop rinsing when most of the soap is gone. Don't. Any dirt left on the car will be dragged by your drying towel and mar the paint. Rinse from top to bottom, with extra attention to gaps, mirrors, grilles and lower sections.

6. DRY WITHOUT SCRATCHING

Avoid squeegee blades and chamois – they trap dirt and drag it over the paint. Use a plush drying towel like Q²M SilkDryer, wipe lightly from top to bottom in straight lines and let the towel do the work. Keep separate towels for paint, wheels and lower parts. Misting the towel with a quick detailer adds lubrication and gloss. (Full guide: How to dry your car without scratching it.)

7. EVERY 3 MONTHS: CHEMICAL DECONTAMINATION

On the clean, damp car, spray Q²M Tar, let it work without drying, rinse; then repeat with Q²M Iron. This removes embedded contamination and restores hydrophobicity. (Full guide: What is chemical decontamination.)

8. AFTER THE WASH

Empty and rinse your buckets thoroughly – emptying alone doesn't remove the grime – and cover them. Wash your mitt and towels with Q²M TowelWash and let them air dry.

What you need

Q²M Bug&Grime bugs and road film

Q²M Foam snow foam pre-wash

Q²M Bathe pH-neutral shampoo

Q²M Tar and Q²M Iron quarterly decontamination

Q²M Smoothie wash mitt

Q²M SilkDryer drying towel

Q²M TowelWash towel detergent

2 buckets with grit guards, a pressure washer and foam lance

GYEON tip

Washing often is good – washing wrong is the problem. A light wash every two weeks is easier and safer than a big scrub every two months.

Back to contents ↑
Knowledge #

5 most common mistakes when washing a car

We all made these at least once. Avoid them and your paint will thank you.

We've all made these mistakes at least once. Detailing is a constant learning process – here are the five most common ones.

In short

Wash top to bottom and never go back up, do one wheel at a time, do the wheels before rinsing the car, never wash hot panels or in direct sun, and ditch blades, chamois and sponges.

What you need

Q²M Bathe and Q²M Smoothie two-bucket wash

Q²M IronWheelCleaner wheels

Q²M SilkDryer drying towel

Step by step

  1. Going back up: wash top to bottom and once your mitt has touched the lower part of a panel, never go back up. Use two buckets and rinse the mitt after each panel.
  2. All wheels at once: never spray all four wheels and let the product dry while you finish the first. Work on one – maximum two – wheels at a time.
  3. Rinsing first: start with the wheels, but don't rinse the car before. Cleaning four wheels takes about 30 minutes – don't let water sit on the paint all that time.
  4. Heat: don't wash in direct sun and make sure paint and wheels are cool. Especially on black cars, water and chemicals leave deposits quickly on hot surfaces.
  5. Wrong tools: water blades, chamois and scratchy sponges are fast – and leave an incredible amount of defects. Use microfibre mitts and drying towels.

GYEON tip

Early morning or evening in the shade is the best time to wash.

Back to contents ↑
Knowledge #

Can you wash your car too often?

Frequency isn't the problem. Technique is.

Every week? Every two months? Can washing too often damage your paint?

In short

No – if you wash safely. Regular washing actually means lighter, easier washes because contaminants don't get time to bond. A good rule of thumb: every two weeks or 2,000 km, more often with salt, bird droppings, sap or dust.

The background

The real risk is how you wash: skipping the pre-wash, using one bucket, washing in direct sun, not drying the car, or using harsh cheap cleaners. That's what leads to scratches, water spots, stained trim and failing protection. Little and often, done right, is best.

Protection helps too: from Q²M WetCoat to Q² Syncro EVO, GYEON products repel water and dirt so your car stays clean longer.

What you need

Q²M Foam and Q²M Bug&Grime pre-wash

Q²M Bathe or Q²M Bathe+ shampoo

Q²M Smoothie wash mitt

Q²M SilkDryer drying towel

Q²M CeramicDetailer drying aid

Step by step

  1. Pre-wash with Q²M Foam and Q²M Bug&Grime.
  2. Wash with Q²M Bathe or Bathe+ and a Q²M Smoothie, two-bucket method.
  3. Always dry the car – Q²M SilkDryer with Q²M CeramicDetailer as a drying aid keeps the surface slick and glossy.

GYEON tip

Little and often beats a big scrub every two months.

Back to contents ↑
Knowledge #

How to dry your car without scratching it

How to dry your car without scratching it

Drying is where many scratches happen. Here is how to do it safely.

You've washed carefully – don't ruin it while drying. It is almost impossible to remove every speck of dirt when washing, and the drying tool decides what happens to it.

In short

Avoid squeegees and chamois leathers. Use a plush, deep-pile drying towel like Q²M SilkDryer, wipe lightly top to bottom in straight lines, and use separate towels for paint, wheels and lower parts.

The background

Squeegee blades and chamois trap dirt particles on their edge or face and drag them over the paint. A deep-pile microfibre lets specks sink into the pile, away from the paint. An air or leaf blower is also a great non-contact option.

What you need

Q²M SilkDryer plush drying towel

Q²M TowelWash towel detergent

Separate towels for wheels and lower parts

An air blower (optional)

Step by step

  1. Dry the paint from top to bottom in straight motions.
  2. Don't apply pressure – let the towel do the work.
  3. Use separate drying towels for paint, wheels and lower parts.
  4. Use a blower for mirrors, grilles and gaps.
  5. Wash your towels after every wash with Q²M TowelWash, without conditioner, and let them dry quickly.

GYEON tip

Mist a quick detailer onto your drying towel – it adds lubrication and gloss as you dry.

Back to contents ↑
Knowledge #

How to use quick detailers properly

How to use quick detailers properly

Used right, a quick detailer adds gloss and slickness. Used wrong, it adds swirls.

Quick detailers are a great way to add gloss and slickness. But often advertised as 'waterless', they can turn your paint into a nest of swirls if used wrongly.

In short

Only use a quick detailer on a clean car. The best use: as a drying aid on the wet car, or to remove water spots and wax residue on a dry, clean car.

The background

Using a quick detailer to wipe dust and dirt off before a car show just drags grime over the paint – and creates defects.

What you need

Q²M SilkDryer drying towel

Q²M SoftWipe final wipe

Step by step

As a drying aid:
  1. Wash the car; it's still wet.
  2. Mist your drying towel and the panel with Q²M QuickDetailer or Q²M CeramicDetailer.
  3. Dry in straight lines with light pressure, re-applying as you go – don't overuse it.
  4. Final wipe with a Q²M SoftWipe for a slick, glossy finish.
On a dry, clean car (water spots, wax residue):
  1. Mist the panel and a first towel.
  2. Wipe in straight lines with little pressure.
  3. Buff with a second towel to a streak-free gloss.

GYEON tip

A good quick detailer works on every surface – paint, plastic and wheels.

Back to contents ↑
Real-life fix #

The pros and cons of automatic car washes

Quick and convenient – but at what cost to your paint?

Automatic car washes are quick and convenient. But they may come with hidden costs.

In short

The large brushes are made of coarse cords spinning at high speed – they essentially whip your bodywork, and over time damage the clear coat. Hand washing is slower but much safer.

The background

The downside of hand washing: it takes time and some investment in the right products. The good news: with a good routine, it takes less time than you think.

What you need

Q²M Bathe shampoo

Q²M Smoothie wash mitt

Q²M SilkDryer drying towel

Q²M Foam pre-wash

Step by step

  1. Pre-wash with Q²M Foam.
  2. Two-bucket wash with Q²M Bathe and Q²M Smoothie.
  3. Dry with Q²M SilkDryer.

GYEON tip

Coated car? Brush car washes damage coatings too – hand wash only.

Back to contents ↑
Knowledge #

What is an undercarriage wash – and why your car needs one

Most people clean what they see. What's under your car matters just as much.

Most people clean what they see – and leave the engine bay and undercarriage with their build-up of grime.

In short

An undercarriage wash uses water and chemical decontamination to remove salt, de-icing chemicals and tar from under the car. Doing it once or twice a year helps prevent rust.

The background

In winter, salt and de-icing chemicals are sprayed into the wheel arches, subframe, suspension and underbody – and speed up rust. In summer, roadworks after the winter add tar deposits. That's why undercarriage washes are so popular in countries with harsh winters.

What you need

A pressure washer (an underbody lance helps)

Step by step

  1. Rinse the underbody and arches thoroughly.
  2. Apply Q²M APC to break down grime and salt; use Q²M Tar on tar deposits.
  3. Let it dwell, then rinse thoroughly.
  4. Repeat once or twice a year – ideally after winter.

GYEON tip

Do it after winter, before the salt has had months to work.

Back to contents ↑
Knowledge #

Deep crevice cleaning: the safe way

Brushes seem like the obvious choice for crevices. They're not.

Attention to detail matters most in tight crevices – especially around piano black trim. Detailing brushes seem the obvious tool, but they scratch piano black easily and have very little surface contact.

In short

After the pre-wash, flush the crevices with Q²M APC or Q²M Bug&Grime, then clean them with a microfibre wrapped around a vinyl wrap squeegee tool, turning the towel after each pass.

What you need

A microfibre towel

A vinyl wrap squeegee or plastic trim tool

Step by step

  1. Complete your pre-wash.
  2. Flush the crevices thoroughly with Q²M APC or Q²M Bug&Grime.
  3. Wrap a microfibre around the squeegee tool and run it through the gap from one end to the other.
  4. Rotate the towel after each pass for a clean edge.
  5. Continue with your contact wash.

GYEON tip

This works for panel gaps around the whole car, not only piano black.

Back to contents ↑
Knowledge #

Complete exterior detail: step by step

The full exterior routine, in the right order, with the right products.

Want to do a complete exterior detail? Here is the full process – in the right order.

In short

Wheels and tyres (off the car if possible), arches and calipers, door shuts, pre-wash, contact wash, protection, careful drying and a tyre dressing to finish.

What you need

Jack, brushes, a plastic trim tool

Step by step

Wheels:
  1. Remove the wheels one by one. Spray Q²M IronWheelCleaner on the dry wheel and let it work.
  2. Spray Q²M TireCleaner on the sidewalls and agitate with a tyre brush.
  3. When the wheel cleaner turns purple, rinse. Wash with Q²M WheelMitt and shampoo, rinse.
  4. Spray Q²M WetCoat and rinse for protection.
  5. With the wheel off, clean the inner arch and suspension with Q²M APC and rinse. Spray Q²M Iron on the calipers to remove fallout. Finish with Q²M WetCoat and rinse.
Body:
  1. Door sills and shuts: soak with Q²M APC, agitate with brush and mitt, rinse.
  2. Bumpers and mirrors: Q²M Bug&Grime, let it dwell.
  3. Foam the whole car, dwell a few minutes, rinse.
  4. Panel gaps: wrap a soapy microfibre around a plastic trim tool and work through the gaps.
  5. Contact wash: a couple of capfuls of shampoo in the bucket; wash top to bottom in side-to-side lines. Rinse.
  6. Protection: Q²M Bathe+ through the foam gun, or Q²M WetCoat. Final rinse.
  7. Blow-dry if possible, then finish with a drying towel misted with Q²M QuickDetailer.
  8. Final touch: Q²M TireExpress on the tyres.

GYEON tip

Work side to side rather than up and down – you won't drag dirt up from the lower panels.

Back to contents ↑
Chapter 03

Decontamination

Some dirt bonds to the surface and a normal wash will not move it. Here is how to dissolve, lift and clay it away safely – and how to deal with the everyday emergencies, from bird droppings to bugs.

Decontamination
Knowledge #

What is chemical decontamination – and how to do it

Your paint collects more than you can see. Chemical decontamination removes it – without touching the paint.

Over time, coated or bare paint collects contamination: iron fallout, dust, sand, mineral deposits, acid stains, tree sap, oils, tar, grime and insects. It dulls the gloss and kills the performance of your protection.

In short

Chemical decontamination removes contamination with chemistry instead of physical contact (like clay). Every 3 months, spray Q²M Tar and then Q²M Iron on the clean, damp car, let them work and rinse.

The background

Mechanical decontamination (clay) removes contamination through physical contact – and can mar the paint. Chemical decontamination does it without contact, so it is safe to repeat regularly and keeps your protection performing at its best.

What you need

Q²M Tar tar and organic contamination

Q²M Iron iron fallout

A pressure washer

Step by step

  1. Wash the car; leave it damp.
  2. Spray Q²M Tar. Let it sit but don't let it dry.
  3. Rinse thoroughly. Inspect and re-apply if needed.
  4. Repeat the process with Q²M Iron.

GYEON tip

Do it every 3 months – it restores hydrophobicity and keeps your coating performing.

Back to contents ↑
Knowledge #

When (and how often) to clay your car

When (and how often) to clay your car

Clay is not a maintenance product. Here's when it makes sense – and when it doesn't.

The clay bar is the best-known way to remove contamination a wash won't pick up – brake dust, organic deposits, industrial fallout. But it is often used at the wrong moment.

In short

Clay is abrasive and can leave marring. Use it as a last resort, before polishing or coating – not as part of your maintenance wash. Try chemical decontamination first.

The background

It's a common misconception that you should clay between washing and protecting. Clay bars are abrasive putty: they lift embedded contaminants but can mar the paint, which then needs a polish to correct.

How many times can you clay? As many as you like – clay doesn't remove clear coat. But the marring it leaves means polishing, and polishing does remove a little clear coat.

What you need

Q²M Iron and Q²M Tar try these first

Q²M Clay Bar in different grades

Clay lubricant

Step by step

  1. Add chemical decontamination to your regular routine – it stops contamination taking hold, so you rarely need clay.
  2. Before polishing or coating, feel the paint with a clean hand. Still rough? Clay.
  3. Use plenty of lubricant, light pressure and straight lines. Fold the clay often.
  4. Polish afterwards to remove any marring.

GYEON tip

Clay is safe on glass – and recommended before applying a glass coating like Q² View EVO.

Back to contents ↑
Product guide #

RestartWash REDEFINED: why a coated car sometimes needs an acidic wash

When your coating stops beading, it's usually buried under minerals and iron. An acidic wash brings it back.

Your coated car used to bead like new – and now water just sits there. In most cases the coating is still there, covered by a film of mineral deposits (water spots, limescale) and iron particles. That's what an acidic decontamination wash is for.

In short

Q²M RestartWash REDEFINED is an acidic shampoo (pH 4 concentrate) for coated cars. It removes mineral and ferrous contamination in a single wash and restores the coating's water behaviour and slickness – without adding anything that masks the result.

In detail

WHY ACIDIC?

Regular pH-neutral shampoos are made to be gentle and don't dissolve mineral deposits. Water spots and limescale are alkaline mineral residue – an acidic wash dissolves them, while also removing iron particles.

WHAT IT DOES – AND DOESN'T
  • Removes water spots, limescale and iron particles in one wash.
  • Restores the coating's original beading and slickness.
  • Adds no protection of its own, and masks nothing – you see the real condition of your coating.
  • Doesn't repair a worn or damaged coating.
WHEN TO USE IT

When your coated car starts losing its water repellency. For routine washes, use Q²M Bathe; for heavy contamination, a dedicated product such as Q²M TotalRemover.

What you need

Two buckets

Foam lance (optional)

How to choose

  1. Rinse the car.
  2. Dilute: 1:500 for a periodic refresh or light contamination, 1:250 standard, 1:100 for intensive decontamination. In a foam lance: 40 ml in 500 ml of solution.
  3. Wash panel by panel.
  4. Rinse thoroughly – never let it dry on the surface.
  5. Dry and check the beading.
  6. Want extra protection? Follow up with Q²M CeramicDetailer or Q²M Cure REDEFINED.

GYEON tip

On a waxed or sealed car, test on a small area first – acidic decontamination can affect some waxes and sealants.

Back to contents ↑
Knowledge #

When to use Q²M TotalRemover

Before a new coating, the old protection has to go. That's TotalRemover's job.

Before you correct and coat, the old protection needs to go – otherwise the new layer can't bond properly.

In short

Use Q²M TotalRemover in the preparation wash before paint correction and coating, on clean, wet paint. It removes and degrades old coatings, sealants and waxes so the new protection bonds properly.

The background

Bonus: it's also very effective on windows full of water spots.

What you need

Q²M Prep final wipe before coating

Step by step

  1. Wash the car.
  2. Apply Q²M TotalRemover on the clean, wet paint as directed on the label.
  3. Rinse.
  4. Continue with correction, Q²M Prep and coating.

GYEON tip

Use it on heavily spotted glass too.

Back to contents ↑
Real-life fix #

Water spots: how to remove and prevent them

Water spots: how to remove and prevent them

Water evaporates, minerals stay. Here's how to remove water spots before they etch.

Water spots are mineral deposits: the water evaporates, but the minerals in it stay behind as a residue on your paint.

In short

Light spots: wash with hot water and a degreaser. Medium spots: use Q²M WaterSpot. Severe spots: machine polishing. Prevent them by drying your car and never letting water evaporate in the sun.

The background

A water droplet works like a magnifying glass: the sun heats the surface below it and the droplet evaporates faster, leaving more minerals behind. That's why a well-beading car can still show droplets while the unprotected car next to it is already dry – and why drying matters.

What you need

Q²M WaterSpot dedicated water spot remover

Q²M Prep to wipe off after treatment

Q²M SilkDryer to prevent spots

Clean microfibre towels

Step by step

  1. Wash the car – regular washing removes most light spots.
  2. If spots remain, spray Q²M WaterSpot on the panel.
  3. Load a clean microfibre with plenty of product for lubrication.
  4. Work in straight lines in both directions for good coverage.
  5. Leave it on the panel for a while to break down the minerals.
  6. Wipe down with Q²M Prep to remove all product.
  7. Severe spots that remain need machine polishing (in extreme cases, a respray).

GYEON tip

Always dry your car after washing – and after rain on a sunny day.

Back to contents ↑
Real-life fix #

Tar spots and organic contamination on your car? How to remove them

Tar spots and organic contamination on your car? How to remove them

Black spots on the lower panels? Tar and organic contamination come with driving. Here's the safe way to remove them.

Tar residue and organic contamination build up on every car with use – especially on the lower panels behind the wheels.

In short

On the washed, still damp car, spray Q²M Tar on the contaminated areas, let it dwell (it changes colour as it reacts) without drying, rinse and repeat if needed. Q²M SilkMitt helps on stubborn spots.

The background

Where you park matters too: trees, construction sites and industrial areas all add organic contamination. Check your parking spot to reduce it.

What you need

Q²M SilkMitt mitt designed for use with Tar

Step by step

  1. Wash the car and leave it damp.
  2. Spray Q²M Tar liberally on the contaminated areas.
  3. Let it dwell – it slightly changes colour as it reacts. Don't let it dry.
  4. Rinse thoroughly. Inspect and re-apply if necessary.
  5. For more effective removal, gently agitate with Q²M SilkMitt.

GYEON tip

Lower panels behind the wheels collect the most tar – check them at every wash.

Back to contents ↑
Real-life fix #

Bird droppings on your car? Remove them without scratching

Don't grab the kitchen towel. Bird droppings are acidic and full of grit – here is how to remove them safely, at home or on the go.

You come back to your car and there it is. The first reflex – grabbing a tissue or an old cloth and wiping – is one of the quickest ways to scratch your paint. Bird droppings are highly acidic and can etch any exterior surface, coated or not, if left too long.

In short

Don't wipe. Soften the dropping with a cleaner or lots of lubrication, let it dwell, rinse it off if you can – otherwise dab and lift with a soaked microfibre towel.

The background

First, assess:
  • Is your paint protected? Without a coating or wax you have less time before the clear coat is attacked.
  • How long has it been there – minutes, or days baked on by the sun?
  • Can you wash the car now? If yes, a non-contact approach is always the safest.

What you need

Q²M QuickDetailer lubricant (or Q²M Bathe mixed 1:100 with water)

A clean, long-pile microfibre towel

Pressure washer or hose (if available)

Step by step

At home – non-contact:
  1. Spray the area with Q²M Bug&Grime or diluted Q²M APC.
  2. Let it dwell until the dropping starts to break down. Don't let it dry.
  3. Rinse off. Repeat if needed, then continue with your normal wash.
On the go, or if remnants stay – dab, don't wipe:
  1. Spray Q²M Bug&Grime again and let it work.
  2. Soak a clean long-pile microfibre with Q²M QuickDetailer (or pH-neutral shampoo mixed 1:100 with water).
  3. Place the towel over the spot and dab lightly so the fibres pick up the remains.
  4. Lift and inspect. Repeat with a clean side of the towel.
  5. Once everything is trapped in the towel, fold it and wipe once for the final finish.

GYEON tip

Keep a bottle of quick detailer and a clean microfibre towel in the boot. Acting within minutes makes all the difference.

Back to contents ↑
Real-life fix #

Bugs all over the front of your car? Remove them safely

Summer evening drives end one way: a bug-covered front end. Here's how to remove them without scrubbing.

Spirited summer evening drives can end only one way – with the whole front of your car covered in bug splatter. You can't prevent it, but you can remove it easily.

In short

Work on a cool car in the shade. Rinse, spray Q²M Bug&Grime generously, let it dwell 1–2 minutes and rinse off with a pressure washer. Then do your normal wash.

The background

Bug remains are acidic and bake on in the sun – the sooner you remove them, the easier it is and the less risk of etching.

What you need

A pressure washer

A short-pile wash mitt (optional)

Step by step

  1. Let the car cool down and work in the shade.
  2. Rinse the affected areas thoroughly to remove as much debris as possible.
  3. Spray Q²M Bug&Grime liberally.
  4. Let it dwell 1–2 minutes – don't let it dry.
  5. Blast off the remains with the pressure washer. Agitate stubborn spots gently with a short-pile mitt if needed.
  6. Continue with your contact wash.

GYEON tip

A protected paint (wax or coating) makes bugs much easier to remove next time.

Back to contents ↑
Real-life fix #

Overspray on your car? How to remove it

Overspray is airborne paint that hardens on your car. Here is how to find it and remove it safely.

Overspray is another form of contamination – usually paint mist from a body shop or smart repair on your car or one nearby. It lands on your paint, settles and hardens over time.

In short

Wash, decontaminate chemically, then clay – start with a mild clay bar. Finish with a polish to remove any marring from claying.

The background

Overspray is hard to see. Glide a clean hand lightly over the paint – you will feel (and hear) the roughness.

What you need

Q²M Iron and Q²M Tar chemical decontamination

Q²M Clay Bar mild first, coarser if needed

Q²M Bathe wash

Step by step

  1. Wash the car safely.
  2. Decontaminate chemically.
  3. Clay with plenty of lubricant, starting with a mild clay bar; move to a coarser one only if needed.
  4. Polish (ideally by machine) to remove the marring from claying.
  5. Protect the paint.

GYEON tip

Feel the paint inside a thin plastic sandwich bag – it makes contamination much easier to detect.

Back to contents ↑
Real-life fix #

How to remove car badges and emblems safely

De-badging is easy – if you never use a screwdriver.

Want a cleaner look? Removing badges is easy with the right method – and risky with the wrong one.

In short

Heat the badge to soften the adhesive, saw behind it with fishing line or dental floss, then remove the residue with Q²M Tar and a Q²M PolishWipe.

The background

Never pull with your fingertips or lever with a screwdriver: the badge can bend or crack, and its other edge can dig into the paint.

What you need

A heat gun or hairdryer

Fishing line or strong dental floss (30–45 cm)

Step by step

  1. Check what the panel is made of – plastic and composite need extra care and less heat.
  2. Heat the badge for about 30 seconds, keeping the gun moving.
  3. Slide the line behind the top edge and saw side to side, working down to the bottom. Careful – the badge may still be hot.
  4. Inspect for adhesive residue.
  5. Apply Q²M Tar directly onto the residue and wipe away with a clean Q²M PolishWipe.

GYEON tip

Protect the area afterwards – the paint under the badge has never seen a wax or coating.

Back to contents ↑
Chapter 04

Polishing & paint correction

Polishing is the only way to truly remove swirls and light scratches. Learn which defects you can fix, by hand or by machine, and which pads and machines to use.

Polishing & paint correction
Knowledge #

Paint defects you can easily remove yourself

Not every defect needs a professional. These you can fix at home, by hand.

A classic car park scuff with paint from another car, or lacklustre, dull paint – you can restore these at home.

In short

A quality one-step polish and clean microfibres are all you need: work a small amount in circles over the defect and buff off.

What you need

Step by step

  1. Wash and dry the area.
  2. Put a small amount of polish on a microfibre cloth.
  3. Work it in circular motions over the defect.
  4. Buff off with another clean microfibre.
  5. Repeat if needed.

GYEON tip

Protect the polished area afterwards – a quick coat of Q² Wax or Q²M WetCoat will do.

Back to contents ↑
Knowledge #

Which defects can you remove by hand polishing?

No machine, no problem. Some areas are actually better done by hand.

No budget or confidence for machine polishing? You can still get good results by hand – and some areas of your car are not safe or practical to machine polish anyway.

In short

Hand polishing works well for door handle areas, thin pillars, painted interior trim, exterior metal trim, around and under spoilers, and light paint transfer.

What you need

Masking tape

Step by step

  1. Clean the area.
  2. Mask around trim so the product stays where you want it.
  3. Apply a small amount of polish to the applicator and work it in with steady pressure – elbow grease, but not heavy-handed, or you will create new defects.
  4. Buff off with a clean microfibre.
  5. Always finish with a layer of protection.

GYEON tip

Too much pressure creates defects – let the polish do the work.

Back to contents ↑
Complete guide #

Machine polishing for beginners

Machine polishing for beginners

Machine polishing isn't magic – it's preparation, testing and technique. Everything to get started safely.

Polishing only ever removes clear coat – it never adds any. That's why good polishing is about doing as little as necessary, as well as possible. This guide takes you from preparation to finish.

In short

Prepare properly (wash, decontaminate, clay, measure, inspect, mask), do a test spot to find the least aggressive pad and polish that works, keep your technique consistent, respect plastic and carbon panels, and only polish when needed.

Guide

1. 5 THINGS TO DO BEFORE POLISHING
  • Wash and decontaminate chemically – no hidden contamination may stay on the paint. Clay, ideally indoors on dry panels, with plenty of lubricant, in straight lines and sections. Feel each section with a clean hand. Measure paint depth on every panel if you have a gauge, to avoid striking through the clear coat.
  • Inspect the paint with good lighting for defects or previous resprays. Check its condition before masking, so you don't damage it when removing tape.
  • Mask only delicate areas that the pad can damage, and trim you don't want polish on.
2. THE TEST SPOT: FIND YOUR PAD AND POLISH COMBO

Every brand has its own paint – so the same combo gives different results on different cars.

  • Define your goal: refining, gloss, or scratch removal. Mask three test sections of about 45 × 45 cm. Start with your least aggressive pad and polish.
  • Not enough? Change one thing only – pad or polish – and test on the next section. Never go over the same section twice. Let the panel cool, wipe with Q²M Prep and inspect with a light.
  • Keep your pads clean during testing – dirty pads give false results.
3. 1, 2 OR 3 STAGES?

The level of defects decides how many steps you need. A 3-stage correction uses three different polishes (often heavy, medium, finishing) – maximum correction, but a lot of time. Many professionals choose the approach that removes the most defects in the least time.

4. SMAT OR DAT?

SMAT abrasives (Super Micro Abrasive Technology) start small and stay small – you can stop at any point. DAT abrasives (Diminishing Abrasive Technology) break down as you work – stop too early and the result is substandard, and coarse abrasives can cause damage. For beginners, SMAT is more forgiving.

5. TECHNIQUE
  • Stance: balanced and stable, like shooting a rifle or playing snooker. Off-balance moments put uneven pressure on the panel. Arms: elbows bent, like a racing driver – comfortable, with full control and consistent pressure. If you need to stretch, move – or remove the obstacle (open a door, turn a mirror, remove a handle).
6. METAL VS PLASTIC AND CARBON PANELS

Metal disperses heat quickly; plastic and carbon fibre keep it localised. On non-metal panels, keep your working window smaller and check the temperature by hand often.

7. HOW MANY TIMES CAN YOU POLISH?

There's no single answer: it depends on paint thickness and hardness and on how aggressive the polishing is. Refining removes very little; heavy correction removes more. Measure paint depth, polish only when necessary and always start least aggressive.

8. 5 NO-GOS
  • Using worn or damaged pads. Buying all the equipment at once – master one machine first.
  • Overcomplicating with extensions and add-ons. Going in too aggressive – some heavy cutting pads remove clear coat alarmingly fast. Overworking the polish – it's counterproductive and damages pads.

What you need

Q²M Iron , Q²M Tar , Q²M Clay Bar preparation

Q²M Prep to inspect results

Dual-action polisher

Masking tape, inspection light, paint depth gauge (optional)

GYEON tip

Least aggressive first – always. You can take more clear coat off, but never put it back.

Back to contents ↑
Complete guide #

Polishing machines and pads explained

Polishing machines and pads explained

The right machine and the right pad make polishing easier and safer. Here's how to choose – and how to look after them.

Once upon a time the rotary was king. Today there are many machines and pads – but the principles remain the same.

In short

Three machine types: rotary, dual action with forced rotation, and random orbital dual action. Three main pad materials: foam (most versatile), microfibre (clean cut, DA only) and wool (heaviest cut). A mid-cut foam pad is often the do-it-all choice on modern paint.

Guide

1. POLISHING MACHINES
  • Rotary (direct drive) – excellent cutting power and great for final jewelling, but prone to holograms and secondary defects.
  • Dual action, forced rotation – well-rounded across cut, mid and finish, with less cut than a rotary.
  • Dual action, random orbital – from mid-cut to a high finish; the safest choice for beginners.

OPM and RPM ranges matter, and not all random-orbital machines are equal. Start with one machine and master it.

2. POLISHING PADS

Rotary pads are for rotary machines. Eccentric pads are for dual-action machines and usually have a centre hole to let heat escape from the backing plate.

  • Foam – the most adaptable, from final finishing up to heavy cutting.
  • Microfibre – good for heavy and mid cutting with a cleaner cut than heavy foam; DA only.
  • Wool – the go-to for extra-heavy cutting, but leaves defects behind.

Not all pads are equal: a pad like the Q²M Heavy Cut can cut as efficiently as wool and finish as cleanly as microfibre. Keep a variety and learn each pad's limits with different compounds and paints.

3. CLEANING YOUR PADS
  • When you finish with a pad, put it straight into a bucket or sink of clean water – this stops the product drying in.
  • At the end of the job, apply a weak dilution of Q²M APC and work it in by hand or with a soft-to-medium brush.
  • Rinse thoroughly, repeat if needed, and let dry on a drainer.
  • Replace worn or damaged pads – they work slower and give worse results.
4. LOOK AFTER YOUR MACHINE

After a day of polishing, remove dust from the vents and backing plate with a soft brush and a vacuum or airline. Don't wrap the cord tightly around the machine – it can break the inner cable.

What you need

  • Q²M Heavy Cut pad and other GYEON pads (confirm names)

Q²M APC pad cleaning

Dual-action polisher

GYEON tip

Beginner? A random-orbital DA with a mid-cut foam pad covers most jobs.

Back to contents ↑
Knowledge #

Piano black trim: how to polish and protect it

It looks great for about a week. Here is how to bring piano black back.

Piano black trim is everywhere – inside and outside. It is a cost-effective plastic that loses its factory-fresh look quickly.

In short

Clean (and decontaminate if exterior), mask around it, then polish with the least aggressive pad and polish combo. Step up only if needed.

What you need

Q²M Glass and Q²M SoftWipe for gentle cleaning afterwards

Masking tape

Step by step

  1. Clean the trim thoroughly; decontaminate if it's on the exterior.
  2. When dry, mask around it – glass, rubber mouldings, chrome.
  3. Start with the least aggressive pad and polish combination.
  4. If that isn't enough, step up one level.
  5. Maintain with a soft microfibre only – never brushes.

GYEON tip

Prevention: clean piano black only with a soft microfibre like Q²M SoftWipe, never a brush.

Back to contents ↑
Chapter 05

Protection & coatings

Protection is what keeps a clean car clean. Compare coatings, sealants and wax, learn to apply them without high spots, and keep them performing for years.

Protection & coatings
Product guide #

Which GYEON coating is right for you?

Which GYEON coating is right for you?

From a 12-month spray coating to a 50-month two-layer system. Here's how to choose.

GYEON's paint coatings range from a spray-on coating you can apply in an afternoon to a two-layer system that lasts over four years. The right one depends on how long you want protection, how much time you have and how experienced you are.

In short

Q² CanCoat EVO: easiest, up to 12 months. Q² One EVO: simple traditional coating, up to 24 months. Q² Pure EVO: durable one-layer, up to 36 months. Q² Mohs EVO: up to 36 months with one layer, 48 with two. Q² Syncro EVO: two-layer system, up to 50 months. Special finishes and surfaces have their own EVO coatings.

In detail

PAINT COATINGS (real-world lifespan as stated by GYEON)

  • Q² CanCoat EVO – up to 12 months / 12,000 km. Spray onto the microfibre, wipe on, wipe off. Works on paint, trim, metal, rims and side/rear glass. 200 ml, 10–15 ml per car. Easiest choice and a great top-up.
  • Q² One EVO – up to 24 months / 25,000 km. A simple traditional coating with a clean, glossy finish; multiple coats possible (1 hour apart). 30/50/100 ml, 25–30 ml per car.
  • Q² Pure EVO – up to 36 months / 40,000 km. Designed as a one-layer coating; user-friendly even with limited experience. Wipe-off window up to 10 minutes (immediately in hot, humid conditions).
  • Q² Mohs EVO – up to 36 months / 40,000 km with one layer, 48 months / 50,000 km with two. For a long-lasting coating that's still easy to apply. 15–25 ml per car.
  • Q² Syncro EVO – up to 50 months / 50,000 km. Two-stage system: Q² Mohs EVO base plus Q² Skin EVO top coat for extra gloss, slickness and self-cleaning – especially striking on dark paint.
SPECIAL SURFACES
  • Matte or satin paint, matte PPF, wraps → Q² Matte EVO (up to 24 months / 30,000 km).
  • PPF (gloss, satin or matte) → Q² PPF EVO (up to 24 months / 25,000 km).
  • Wheels and clear-coated calipers → Q² Rim EVO (up to 18 months / 45,000 km, heat resistant above 800 °C).
  • Windscreen and exterior glass → Q² View EVO (up to 24 months / 50,000 km).
  • Unpainted plastic trim → Q² Trim EVO.

All EVO coatings are suitable for outdoor application. Keep the surface out of direct sun and away from water for the first 12 hours.

What you need

Q²M Iron REDEFINED and Q²M Tar REDEFINED decontamination

Q²M BaldWipe EVO , Q²M SoftWipe EVO levelling

Q²M Prep degreasing (wait 15 minutes before coating)

Q²M Cure REDEFINED maintenance and early protection

Your coating

How to choose

How to choose:
  1. First coating, little time → Q² CanCoat EVO.
  2. First 'real' coating, want 2 years → Q² One EVO.
  3. Some experience, want one layer and 3 years → Q² Pure EVO.
  4. Want up to 4 years and don't mind a second layer → Q² Mohs EVO.
  5. Want the maximum, especially on dark paint → Q² Syncro EVO.
  6. Matte paint, PPF, wheels, glass or trim → the matching EVO coating.

Not sure? A GYEON certified detailer can apply the professional coatings.

GYEON tip

Durability depends on your wash routine and climate. The right maintenance (see Coated car maintenance) gets you to the upper end of these numbers.

Back to contents ↑
Complete guide #

Car wax guide: wax vs sealant vs coating, and how to wax

Wax isn't dead – it has evolved. What it is, how it compares to coatings, and how to make waxing a joy.

'What's the difference between a wax, a sealant and a coating?' We get the question a lot – the terms are often mixed up. And no, wax isn't dead.

In short

Wax forms a sacrificial layer that doesn't bond permanently. A sealant is synthetic and slightly stronger. A ceramic coating cures and bonds chemically to the paint – far more durable. Q² Wax is a fluorine-based wax: easy on, easy off, on bare paint or on top of a coating.

Guide

1. WAX, SEALANT, COATING – THE DIFFERENCES
  • Wax – blends of 'malleable solids' like carnauba, montan, paraffin or synthetics. It forms a sacrificial layer and doesn't bond permanently.
  • Sealant – traditionally a synthetic product mimicking wax; slightly stronger, but still sensitive to heat and chemicals.
  • Coating (ceramic, silica, quartz, SiO₂) – cures after application and bonds chemically to the surface. Once cured, it's extremely resistant to water, chemicals, heat, UV and harsh detergents.

Which one is best? The one that matches your expectations and how you use your car.

2. WHY Q² WAX

A fluorine-based wax that adds outstanding gloss, UV protection and great hydrophobic properties – and is super easy to apply and wipe off. It's also the perfect top coat for a ceramic-coated car.

3. HOW TO APPLY IT
  • Wash and decontaminate the car; park it in the shade.
  • Apply a thin, even layer with the foam applicator – evenly, no heavy spots.
  • Leave it 30–45 minutes – or overnight in a garage for the easiest wipe-off ever.
  • Remove most of the residue with a first microfibre, then a final wipe with a second towel.
4. USING THE WAX STICK
  • Turn the base clockwise to push the wax out – only 2–3 mm above the cylinder.
  • Strike the foam applicator across the top 2–3 times – a thin layer is all you need.
  • Push out more as it wears down, but don't over-extend.
  • To retract, place the clear cap on top, press lightly and turn anti-clockwise – no stress on the thread.
  • Leave the clear cap on and screw on the lid for an airtight seal.

What you need

Q²M Iron and Q²M Tar preparation

Q² CanCoat EVO if you want coating-level durability

Two clean microfibre towels

GYEON tip

Short on time? Wax the paint and, while it sits, coat your windscreen – see Only have an hour?

Back to contents ↑
Knowledge #

Can I apply wax on top of my ceramic coating?

Yes, you can. GYEON developed a fluorine-based wax made to sit on top of your coating. Here is how to apply it.

A coating is your long-term protection. A wax on top is the finishing touch – easy to apply, and a nice way to refresh the look of a coated car.

In short

Absolutely. Q² Wax is a fluorine-based wax developed by GYEON as an easy top coat for ceramic-coated cars.

What you need

A clean microfibre towel

Step by step

  1. Start with a clean, dry car.
  2. Apply an even, thin layer of Q² Wax over the entire paintwork.
  3. Leave it for at least 30 minutes.
  4. Buff off.

GYEON tip

If you have a garage, leave the wax on overnight – it buffs off even more easily.

Back to contents ↑
Complete guide #

How to apply a ceramic coating: the complete guide

How to apply a ceramic coating: the complete guide

Coating is simple if you are methodical. This is the complete process – and the mistakes to avoid.

Applying a coating is relatively simple – as long as you are methodical and follow some basic rules. Most problems come from preparation, levelling or impatience. This guide covers it all.

In short

Wash and decontaminate, polish if possible, degrease properly with Q²M Prep, apply in shoulder-width squares, level with two or three different towels, inspect every panel, and let the coating cure – it takes 7–21 days to reach full hardness.

Guide

1. PREPARATION
  • Read the instructions and have all products ready – no interruptions once you start.
  • Wash and decontaminate thoroughly so no contamination is embedded in the paint.
  • Work indoors if you can. Most GYEON coatings can be applied outside, but a garage makes it easier and faster.
  • If you have a machine polisher, a one-step polish puts the paint in its best condition.
2. DEGREASING – AND WHY IPA ALONE ISN'T ENOUGH

After polishing, oils and fillers stay on the surface and in its pores. They can hide scratches that are only filled, not removed – and they stop the coating from bonding. The rule: if you couldn't paint on the surface without bonding problems, you can't coat it.

IPA alone isn't the answer: it flashes off very fast and can dry the oils into a residue that's even harder to remove; strong IPA can stain plastic trim, and diluting with tap water can leave mineral deposits.

The best method: a degreaser wash, a slow panel wipe, and Q²M Prep as the final step. Q²M Prep is IPA-based, but blended for this job – and its anti-static properties reduce dust bonding.

3. APPLICATION
  • Wear nitrile gloves.
  • Shake the bottle, wipe any crystallised product off the bottle edge, and apply a good amount to the applicator without touching it with the bottle.
  • Work in squares about shoulder-width (max. 40 × 40 cm). The pattern doesn't matter – the result must be an even layer.
  • Wipe most of it off with a short-nap towel (Q²M BaldWipe), then buff with a longer-nap towel (Q²M PolishWipe) slightly beyond the coated area. First time? Use a third towel (Q²M SoftWipe) as a safety blanket. Different towels help you remember which is which.
  • Inspect each panel with diffused light from several angles. After the next panel, check the previous one again for carry-over.
4. HOW TO AVOID HIGH SPOTS

A high spot is coating that wasn't removed properly – it cures into a darker, visible patch, and in most cases the only fix is polishing and re-coating. Avoid it with: a stable environment (same temperature and humidity throughout), enough good towels, small sections, and indirect light to check every panel.

5. DRY VS CURE

Within 12–24 hours, a coating goes from liquid to a gel-like state – that's drying. But dry is not cured: full curing, where the coating builds its adhesion and hardness, takes 7–21 days depending on the conditions. Keep the car indoors for 24 hours if possible, and apply Q²M Cure before going outside – it protects against water spotting in the first weeks.

6. 5 COMMON MISTAKES
  • Poor preparation – no proper wash, decontamination, polish and panel wipe.
  • Incorrect application – too much product, not levelling, poor working conditions.
  • Old coatings – a bottle that's been open in the cupboard for years gives a substandard result.
  • Sub-standard cloths – cheap, used or dirty towels cost you much more time.
  • Ignoring the drying time – good things come to those who wait.
7. STORING AN OPENED BOTTLE

Clean the dropper, close tightly with the original cap, seal the top with tape and store somewhere dark, cool and stable. Always check the recommended shelf life once opened.

What you need

Q²M Iron and Q²M Tar decontamination

Q²M TotalRemover degreasing wash

Q²M Prep panel wipe

Q²M Cure protection while curing

Nitrile gloves, inspection light

GYEON tip

Spotted a high spot while it's still fresh? A little more coating on the area softens it so you can level it straight away.

Back to contents ↑
Knowledge #

How to avoid high spots when applying a coating

How to avoid high spots when applying a coating

The most common mistake with a first coating – and four simple ways to avoid it.

Probably the most common issue when applying a coating for the first time. A high spot is an area where the coating was applied but not correctly removed. Once cured, it shows as a darker patch, especially in cloudy light – and 90% of the time, the only fix is polishing the panel and re-coating.

In short

Work in a stable environment, use three good towels, coat small sections (max 40 × 40 cm) and wipe immediately, and check every panel under diffused light from several angles.

What you need

Diffused inspection light

Step by step

  1. Apply in a stable environment – same temperature and humidity for the whole application.
  2. Use multiple towels: one to remove the excess, one to level, one to perfect the finish. Saving on towels can make the job much more expensive.
  3. Work in sections of max 40 × 40 cm – apply and wipe off straight away.
  4. Use indirect, diffused light and check every panel from different angles.

GYEON tip

Spot a high spot while the coating is still fresh? Re-apply a little coating to soften it and level it straight away.

Back to contents ↑
Knowledge #

One coating for all surfaces? Meet Q² CanCoat EVO

One coating for all surfaces? Meet Q² CanCoat EVO

Too many coatings, too much confusion. What if one did it all?

The range of coatings available is a little overwhelming, if not confusing. If only there was one coating safe on all surfaces...

In short

Q² CanCoat EVO is the one-coating-does-all solution. It works on paint, alloy wheels, trim, engine bay mouldings, exhaust tips, carbon fibre and even PPF and vinyl – and is also a great top coat.

The background

  • Effortless: spray onto a microfibre, wipe on, buff to a gloss.
  • SiO₂-based: long-lasting hydrophobicity, UV protection and a glossy finish that repels dirt.
  • Great value: one 200 ml bottle coats a car 10–15 times.

What you need

Q²M Bathe wash

Q²M Prep degrease

Clean microfibre towels

Step by step

  1. Wash the car and make sure it is completely dry and cool.
  2. Wipe down with Q²M Prep to remove oils.
  3. Spray Q² CanCoat EVO onto the microfibre – never directly on the car.
  4. Work in small sections, any motion you like.
  5. Buff to a full gloss.
  6. Keep it dry for 12 hours.

GYEON tip

Work away from wind and direct sunlight for a streak-free result.

Back to contents ↑
Real-life fix #

Only have an hour? How to protect your car

No time? One hour is enough to protect your paint and your windscreen.

Busy lives don't always leave time for car care. So what can you do with just one hour?

In short

On a clean car, apply Q² Wax. While it sits, clean the windscreen and apply Q² QuickView. Then buff off both. Done.

Step by step

  1. Start with a clean, dry car.
  2. Apply a thin layer of Q² Wax – 2–3 strikes of the applicator across the stick is plenty. Tight circular motions work well.
  3. Leave for at least 30 minutes.
  4. Meanwhile, clean the windscreen with Q²M Glass.
  5. Apply Q² QuickView in tight circles, pressing relatively hard to drive it into the glass. Leave 5–20 minutes.
  6. Buff the paint with Q²M PolishWipe or SoftWipe to a super slick finish.
  7. Buff the glass with a damp Q²M BaldWipe. Your car is protected in one hour!

GYEON tip

Use waiting times smartly – that's how one hour becomes two jobs.

Back to contents ↑
Product guide #

Just picked up a new car? How to protect it from day one

The best time to protect a car is before the first winter, the first car wash and the first scratch.

A new car is the easiest car to protect – the paint is at its best, and there's nothing to correct yet. But 'new' doesn't always mean perfect: cars can pick up contamination and light marks during transport and preparation at the dealership.

In short

Inspect the paint, wash and decontaminate, check whether a light polish is needed, then protect everything: a paint coating, Q² View EVO on the glass, Q² Rim EVO on the wheels and Q² Trim EVO on trim. Then wash safely from day one.

In detail

WHY PROTECT A NEW CAR
  • A coating is easiest to apply on paint that doesn't need correction.
  • Protected surfaces stay cleaner and are easier to wash – from the very first wash.
  • A dealership protection package is often rushed; doing it properly takes time.
CHOOSING THE PROTECTION

What you need

Q²M Bathe , Q²M Iron REDEFINED , Q²M Tar REDEFINED wash and decontaminate

Q²M Prep degrease

Your paint coating

Inspection light

How to choose

  1. Inspect the paint in good light for marks from transport or preparation.
  2. Wash, then decontaminate with Q²M Iron REDEFINED and Q²M Tar REDEFINED.
  3. If there are light marks, a light polish (or Q² Primer) first.
  4. Degrease with Q²M Prep and wait 15 minutes.
  5. Coat the paint, then glass, wheels (ideally off the car) and trim.
  6. Keep the car dry and out of the sun for the first 12 hours.
  7. From now on: safe two-bucket washes and a booster every few weeks.

GYEON tip

Prefer to have it done? A GYEON certified detailer can protect your new car with the professional coatings.

Back to contents ↑
Knowledge #

Will a ceramic coating protect against scratches?

A coating helps – but it is not armour. Here is what to really expect.

One of the most common questions about coatings – and the honest answer matters.

In short

A high-quality coating gives higher scratch resistance than bare paint thanks to its slickness. It won't make your car bulletproof: car-wash brushes, wrong maintenance and vandalism can still cause swirls and scratches.

The background

For maximum protection against both mechanical and chemical impacts, paint protection film (a thick polyurethane film) is the alternative – depending on your budget and expectations.

What you need

Q²M Bathe and a soft wash mitt safe maintenance

Q² CanCoat EVO easy DIY paint coating

Step by step

  1. Coat for slickness, gloss and easier cleaning.
  2. Wash safely – most swirls come from washing, not driving.
  3. Choose PPF for areas that need impact protection.

GYEON tip

Avoid automatic car washes with brushes – they undo the work of any coating.

Back to contents ↑
Product guide #

How long does it last? Durability of GYEON coatings and sealants

From 6 weeks to over 4 years: the real-world lifespan of GYEON protection, in one place.

'How long does it last?' is the question we hear most. Here are the real-world lifespans GYEON states for its protection products – and what makes them last longer.

In short

Sprays and shampoos last weeks (CeramicDetailer up to 6, Bathe+ up to 8, WetCoat up to 12). Q² Wax and Q² QuickView up to 6 months. Coatings last from 12 months (CanCoat EVO) to 50 months (Syncro EVO).

In detail

PAINT COATINGS
SPECIAL SURFACES
WAX, SEALANTS AND BOOSTERS
WHAT DECIDES THE REAL NUMBER

Your wash routine, climate, mileage, where the car is parked, and whether you use automatic car washes. Safe hand washing, regular decontamination and boosters get you to the upper end.

What you need

See the products above

How to choose

  1. Choose a product whose lifespan fits your routine.
  2. Maintain it – see Coated car maintenance.
  3. Re-apply or top up before it's completely gone.

GYEON tip

Lost beading isn't always the end of a coating – decontaminate first, then judge.

Back to contents ↑
Knowledge #

My coating doesn't bead anymore – is it gone?

Not at all. Lost beading is almost always contamination – and it can be fixed.

Your coated car used to bead beautifully – and now water just sits there. Has the coating gone?

In short

No. The main reason beading fades is contamination build-up on top of the coating. Decontaminate, then top up – and the beading comes back.

The background

Hydrophobic properties diminish over time as contamination covers the coating. Chemical decontamination is the most effective way to restore them.

What you need

Q²M RestartWash with Q²M WashPad decontamination wash

Q²M Tar organic contamination remover

Q²M Iron metallic fallout remover

Q²M CeramicDetailer or Q²M WetCoat top-up

Step by step

  1. Switch regularly to a decontamination shampoo: Q²M RestartWash with the Q²M WashPad.
  2. Every 2–3 months, do a stronger decontamination: Q²M Iron over the entire paintwork, Q²M Tar on the lower sections.
  3. Keep the coating topped up with Q²M CeramicDetailer or Q²M WetCoat.

GYEON tip

Beading is a good indicator: when it drops, it's time to decontaminate – not to re-coat.

Back to contents ↑
Complete guide #

Coated car maintenance: the complete guide

Coated car maintenance: the complete guide

A coating makes life easier – if you look after it. Everything you need to know, from the weekly wash to a full top-up.

A ceramic coating is not maintenance-free. The right routine keeps it performing for much longer – and makes every wash quicker. This guide brings together everything: washing, checking your coating, boosting it, decontaminating and topping it up.

In short

Wash with a pH-neutral shampoo and two buckets, dry gently, boost the coating every 4–6 weeks, decontaminate every 2–3 months (or when beading drops) and top up with Q² CanCoat EVO when boosters are no longer enough.

Guide

1. THE REGULAR WASH
  • Pre-wash, then contact wash with Q²M Bathe, two buckets and a quality mitt.
  • Dry with Q²M SilkDryer to avoid water spots.
  • Remove bugs and stubborn residue with Q²M Bug&Grime – it's safe on coated surfaces.
  • Avoid automatic car washes with brushes – they scratch and damage the coating. Never use abrasive sponges or pads.
2. HOW IS YOUR COATING DOING? READ THE WATER

Beading is the visible result of surface tension; sheeting is when water glides off in a sheet. Both are fine – it's a matter of preference. But watch the trend: high beading slowly turns into sheeting and then fades as contamination builds up.

Slickness test: place a microfibre cloth on the bonnet. If it slides down, your coating is slick and healthy. If it doesn't, it needs attention.

Note: extreme beading can cause water spots – round droplets act like magnifiers on a hot panel. Always dry your car.

3. BOOST IT: QUICK OPTIONS
Every 4–6 weeks, or whenever you want more gloss and beading:
  • Q²M Bathe+ – SiO₂ shampoo that leaves a hydrophobic layer while you wash. Alternate it with your usual shampoo.
  • Q²M WetCoat – spray 1–2 times per panel on the wet car after washing, rinse immediately. The fastest option.
  • Q²M CeramicDetailer – wipe on, wipe off on the dry car.
  • Q²M Cure – feeds your coating; also works as a drying aid.
  • Q² Wax – longest to apply, most durable.
4. DECONTAMINATE WHEN NEEDED

Signs: the surface feels rough or gritty, small rust or tar spots appear, the roof, bonnet and boot show staining, beading drops.

  • Regularly: wash with Q²M RestartWash and the Q²M WashPad – it gently removes iron build-up with each wash.
  • Every 2–3 months: after washing, spray Q²M Iron – if it reacts (turns purple), there are iron deposits. Rinse. Then Q²M Tar on small areas at a time, focusing on the lower panels, agitating with Q²M SilkMitt. Finish with a wash.
5. FULL TOP-UP
When boosting isn't enough anymore:
  • Wash thoroughly and decontaminate in several stages – the goal is a surface as clean as the day it was coated.
  • Inspect for damage that needs polishing, and fix it now.
  • Dry fully and wipe every panel with Q²M Prep.
  • Work indoors if possible – otherwise shaded, calm and dry.
  • Spray small amounts of Q² CanCoat EVO onto a fresh microfibre (pointing away from the car), work top to bottom in circles, finish in light straight lines, and buff off immediately with a second towel.
6. DON'T FORGET WHEELS AND TYRES

Protect wheels with Q² Rim EVO and tyres with Q² Tire – they stay cleaner and protected from contamination and UV.

What you need

Q²M Bathe or Q²M Bathe+ shampoo

Q²M SilkDryer drying towel

Q²M Bug&Grime bugs and organic residue

Q²M WetCoat , Q²M CeramicDetailer , Q²M Cure or Q² Wax boosters

Q²M Iron , Q²M Tar , Q²M SilkMitt deep decontamination

Q²M RestartWash and Q²M WashPad decontamination wash

Q²M Prep and Q² CanCoat EVO full top-up

GYEON tip

Lost beading doesn't mean a lost coating – it almost always means contamination. Decontaminate first, then judge.

Back to contents ↑
Product guide #

WetCoat, CeramicDetailer, Cure, QuickDetailer: which spray do you need?

WetCoat, CeramicDetailer, Cure, QuickDetailer: which spray do you need?

The most-asked question about our range. Here's the simple answer.

WetCoat, WetCoat Essence, CeramicDetailer, Cure REDEFINED, QuickDetailer – they're all sprays, but they do different jobs. Here's how to tell them apart.

In short

Q²M WetCoat: spray on the wet car and rinse – fastest protection, up to 12 weeks. Q²M CeramicDetailer: wipe-on SiO₂ detailer for coated cars, up to 6 weeks. Q²M Cure REDEFINED: silica spray sealant that extends a coating's beading and gloss, over 6 weeks. Q²M QuickDetailer: gloss and slickness, removes light dust and spots – not a protection product.

In detail

Q²M WETCOAT – FASTEST
  • Spray-and-rinse hydrophobic sealant: 1–2 sprays per panel on the wet car, rinse immediately with strong pressure.
  • Real-world lifespan up to 12 weeks. About 80 ml per car.
  • Paint, trim, metal, rims and glass; coated or uncoated.
  • Q²M WetCoat Essence: the same idea, concentrated (dilute 1:5 to 1:15) – less product per wash.
Q²M CERAMICDETAILER – WIPE-ON MAINTENANCE FOR COATINGS
  • SiO₂ detailer that combines quick-detailer ease with spray-sealant benefits.
  • On dry or wet paint – also works as a drying aid.
  • Up to 6 weeks. About 40–50 ml per car.
Q²M CURE REDEFINED – THE COATING BOOSTER
  • Silica-based spray that extends a coating's water repellency and gloss, and protects new coatings in their early life. Also works as a sealant on uncoated paint.
  • Over 6 weeks. About 30 ml per car. Don't overuse – it can streak.
  • Gloss finishes only – for matte, use Q²M Cure Matte REDEFINED.
Q²M QUICKDETAILER – GLOSS AND A QUICK FINISH
  • Boosts gloss and slickness, removes light dust, streaks, water spots and fingerprints. Works as a drying aid.
  • Safe on coatings, waxes and sealants – but not a protection product.
AND IN THE BUCKET: Q²M BATHE+

SiO₂ shampoo that adds hydrophobicity while you wash – up to 8 weeks.

How to choose

Quick chooser:
  1. Want protection with zero extra time → Q²M WetCoat during the wash.
  2. Coated car, want a slick boost every few weeks → Q²M CeramicDetailer (also as drying aid).
  3. New coating, or coating losing a bit of gloss and beading → Q²M Cure REDEFINED.
  4. Car show, dust or water spots on a clean car → Q²M QuickDetailer.
  5. Matte car → Q²M Cure Matte REDEFINED.

GYEON tip

Only ever use a quick detailer on a clean car – wiping dust off a dirty car scratches it.

Back to contents ↑
Knowledge #

How to remove an old ceramic coating

Despite the myths, there is only one way to fully remove a coating.

A coating is a hard layer that protects for a long time – but without maintenance it won't last a lifetime. Eventually, it needs to be removed before applying new protection.

In short

The only way to fully remove a coating is polishing. Chemicals and clay change some of its properties but never strip it completely.

The background

A worn layer left on the paint can stop the new product from bonding properly and reduce its durability. Most products work best on bare paint.

What you need

Q²M Prep panel wipe before re-coating

Step by step

  1. Wash and decontaminate the car.
  2. Polish the paint – depending on the coating's abrasion resistance, different pad and compound combos may be needed.
  3. Wipe down with Q²M Prep.
  4. Apply your new protection.

GYEON tip

Polishing removes the coating and prepares the surface in one go.

Back to contents ↑
Real-life fix #

How to protect and maintain a matte paint finish

Matte paint can't be polished back. That makes the right care routine essential.

Matte and satin finishes are more and more popular – from the factory and as wraps. But a matte clear coat can't be corrected: polish out a defect and you change the look of the surface.

In short

Prefer chemical over mechanical decontamination, use a shampoo without gloss enhancers, and protect with products made for matte. For real physical protection, choose matte PPF.

What you need

Q²M Iron and Q²M Tar chemical decontamination

Q²M Bathe shampoo without gloss enhancers

Q² Matte EVO protection without gloss

Matte PPF – physical protection

Step by step

  1. Decontaminate chemically, not mechanically (no clay). Use iron and tar removers with short dwell times, never let them dry, repeat if needed.
  2. Wash with a shampoo without gloss enhancers – they can leave spots that are hard to remove on matte.
  3. Protect with a product made for matte that doesn't add gloss.
  4. Coatings work too, but application is a one-way street: deal with any high spot immediately.
  5. The ultimate protection is matte PPF – ideally on the whole car so the finish stays uniform.

GYEON tip

With PPF on matte, it's all or nothing: cover the whole car to avoid differences in finish.

Back to contents ↑
Knowledge #

Is Q²M TrimCleaner safe on all plastics and trim?

Short answer: yes. Here's how to use it on every type of trim.

Plastics, vinyl, rubber, interior and exterior – can one trim cleaner really handle them all?

In short

Yes. Q²M TrimCleaner is formulated to gently clean a wide range of interior and exterior trim – plastics, vinyl and rubber, as well as hard exterior plastics like spoilers, diffusers and engine covers – without discoloration, fading or damage.

What you need

Clean microfibre towels

Step by step

  1. Test on a small, hidden area first – especially on delicate or unusual finishes.
  2. Apply Q²M TrimCleaner.
  3. Agitate with a brush or Q²M ScrubPad EVO to work it into the grain.
  4. Wipe off with a clean microfibre.

GYEON tip

Protect exterior trim afterwards with Q² Trim EVO.

Back to contents ↑
Knowledge #

Plastic and rubber trim: can you protect them the same way?

Plastic and rubber trim: can you protect them the same way?

Yes – but hard plastic and soft rubber need different products. Here's how.

In a word: yes. But hard plastic and soft rubber trim need different products and approaches.

In short

Hard plastic (spoilers, diffusers, engine covers): clean with Q²M TrimCleaner, wipe with Q²M Prep, coat with Q² Trim EVO. Soft rubber (window seals): clean with Q²M TireCleaner and coat with Q² Tire.

What you need

Clean microfibre towels

Step by step

Hard plastic trim:
  1. Clean with Q²M TrimCleaner, working it into the grain with a brush.
  2. Wipe off the residue with a clean microfibre.
  3. Spray Q²M Prep onto another clean towel and wipe to remove all residue.
  4. Apply Q² Trim EVO with the block and suede (or just the suede on tricky shapes). Apply evenly to avoid patchy areas.
Soft rubber trim:
  1. Clean with Q²M TireCleaner – repeat until the suds are white, not brown.
  2. Once clean and dry, apply Q² Tire with a Q²M MF Applicator.

GYEON tip

Warm the rubber with a hairdryer before coating – it opens the pores, helps the coating work in and increases durability.

Back to contents ↑
Knowledge #

Why protect unpainted plastic trim – and how

Exterior trim faces the elements 365 days a year and rarely gets the care it deserves.

Exterior plastic trim is exposed to the elements 365 days a year – just like your paint – but rarely gets the same care. Properly prepared and protected, it needs very little maintenance afterwards.

In short

Unpainted trim has a grain where dirt takes hold and UV does its work. Clean it with a light APC dilution and a medium-soft brush, dry it and protect it with Q² Trim EVO.

The background

Unpainted trim is rarely completely smooth: the manufacturing process leaves a grain. Dirt and grime take a firm hold in it and become very hard to remove over time. A coating protects against UV, restores the look and stays for a long time.

What you need

Q² Trim EVO durable one-layer ceramic coating for trim

Q²M APC light dilution

A medium-soft brush

Microfibre towels

Step by step

  1. Clean the paint first.
  2. Degrease the trim with diluted Q²M APC and agitate with a medium-soft brush. Rinse and repeat if needed. Less is more: start with a light dilution and never use abrasive tools.
  3. Dry the trim as well as you can.
  4. Apply Q² Trim EVO in a stable environment – a few drops go a long way.
  5. Keep it away from water for at least 24 hours.

GYEON tip

Prefer a dressing instead of a coating? Choose one with the finish you like – some water-based ones can be diluted for satin or matte.

Back to contents ↑
Knowledge #

How to clean and protect carbon fibre

Carbon fibre needs gentle care – and the right protection for its finish.

Carbon fibre parts look amazing – as long as they're cared for gently.

In short

Rinse, wash gently with Q²M Bathe and a microfibre mitt, remove bugs or sap with Q²M Bug&Grime, dry with Q²M SilkDryer and protect with Q² Matte EVO (matte finish) or Q² CanCoat EVO / Q² Syncro EVO (gloss finish).

What you need

Q² CanCoat EVO or Q² Syncro EVO gloss carbon

Q² Matte EVO matte carbon

Soft microfibre mitt and towels

Step by step

  1. Rinse off loose dirt and debris.
  2. Wash gently with Q²M Bathe and a microfibre mitt.
  3. Bugs or sap: spray Q²M Bug&Grime, wait a moment and wipe away with a microfibre.
  4. Dry gently with Q²M SilkDryer.
  5. Protect: Q² Matte EVO for matte finishes, Q² CanCoat EVO or Q² Syncro EVO for gloss.

GYEON tip

Always use soft microfibre on carbon – it scratches more easily than you'd think.

Back to contents ↑
Chapter 06

Wheels, tyres & metal

Wheels collect brake dust, tar and road grime faster than any other surface. Clean them safely, coat them for easy maintenance and finish tyres, arches, chrome and tailpipes.

Wheels, tyres & metal
Knowledge #

How to wash your wheels

How to wash your wheels

Wheels are the dirtiest part of your car. Here's the routine that gets them clean safely.

Wheels collect brake dust, road grime and tar – they are the dirtiest part of your car and should be washed first.

In short

On cool wheels, spray Q²M IronWheelCleaner, scrub the tyre with Q²M TireCleaner, rinse, hand wash the rim with Q²M WheelMitt and WheelBrush, rinse and finish with Q²M TireExpress and Q²M WetCoat.

Step by step

  1. Make sure wheels and brakes are completely cool.
  2. Rinse the wheel and arch to remove loose debris.
  3. Spray Q²M IronWheelCleaner on the whole wheel, inside and out. Let it dwell 2–3 minutes – don't let it dry.
  4. Meanwhile, spray Q²M TireCleaner on the tyre and scrub with Q²M TireBrush.
  5. Rinse the whole wheel.
  6. Hand wash the rim with shampoo, Q²M WheelMitt and Q²M WheelBrush. Rinse.
  7. Apply Q²M TireExpress on the tyre and 1–2 sprays of Q²M WetCoat on the rim – the next wash will be even easier.
  8. Repeat for each wheel, one at a time.

GYEON tip

One wheel at a time – never let wheel cleaner dry on the rim.

Back to contents ↑
Knowledge #

How to clean gloss black wheels without scratching

Gloss black looks amazing – and shows every scratch. Let the chemistry do the work.

Gloss black wheels look fantastic – and scratch easily when you remove brake dust and iron fallout.

In short

On cool wheels, let Q²M IronWheelCleaner dissolve as much as possible before you touch the wheel: apply, let it react, rinse, apply again, then do a gentle contact wash.

What you need

Q²M WetCoat to protect after

Step by step

  1. Make sure the wheels are cool – never hot from driving.
  2. Spray Q²M IronWheelCleaner directly on the dry wheel and let it dwell a few minutes – don't let it dry.
  3. When it turns pink/purple, rinse.
  4. Apply Q²M IronWheelCleaner a second time.
  5. Do a thorough but gentle contact wash with Q²M WheelMitt. Rinse.

GYEON tip

Protect them with a wheel coating like Q² Rim EVO – brake dust sticks less and cleaning gets gentler.

Back to contents ↑
Knowledge #

How to clean tight multi-spoke wheels

How to clean tight multi-spoke wheels

Intricate wheels, simple solution.

Wheel designs are more and more intricate, and tight multi-spoke wheels are common. They can take forever to clean – unless you use the right tools.

In short

Let Q²M IronWheelCleaner dissolve the brake dust, then use the Q²M WheelMitt – your fingers get between and behind every spoke.

Step by step

  1. Spray Q²M IronWheelCleaner on cool wheels and let it work.
  2. Rinse.
  3. Clean between and behind each spoke with Q²M WheelMitt.
  4. Rinse.
  5. Move the car forwards or backwards a little to rotate the wheels, and check the spokes that were hidden.

GYEON tip

Rolling the car half a metre shows the areas you couldn't reach before.

Back to contents ↑
Knowledge #

How to maintain polished lip wheels

Polished lips lose their shine fast. A mild metal polish brings it back.

Polished aluminium lips look great – until they dull.

In short

Clean the wheels with Q²M IronWheelCleaner, then work Q²M MetalPolish into the lip with a Q²M MF Applicator until it turns black, and buff off with Q²M PolishWipe.

The background

Q²M MetalPolish is a mild metal polish – ideal for maintaining the shine on aluminium wheels.

Step by step

  1. Wash the wheels thoroughly with Q²M IronWheelCleaner.
  2. Let them dry.
  3. Dab Q²M MetalPolish around the lip with a Q²M MF Applicator and work it in.
  4. When the product has broken down and the applicator turns black, buff off with Q²M PolishWipe.
  5. Repeat if needed.

GYEON tip

A black applicator is good news – that's oxidation coming off.

Back to contents ↑
Knowledge #

How to prepare and coat your wheels

Coated wheels shrug off brake dust. Here's how to prepare and coat them properly.

Coated wheels are much easier to clean – brake dust and grime simply rinse off. Taking the wheels off makes the job far more efficient.

In short

Remove the wheels, clean them thoroughly with Q²M IronWheelCleaner, degrease with Q²M Prep, then coat in sections starting from the valve and buff off. Inspect with a light.

What you need

A wheel coating Q² Rim EVO is the purpose-built choice

Clean microfibre towels, gloves, a light

Jack, masking tape

Step by step

  1. Jack up the car and remove the wheels. Wrap your locking wheel-nut key in masking tape to avoid scratching around the stud holes.
  2. Don't let the wheel drop onto the caliper when removing it.
  3. Clean the wheels thoroughly with Q²M IronWheelCleaner: spray on cool wheels, let it dwell 1–2 minutes (it changes colour), agitate with a brush or mitt, rinse. Repeat if needed.
  4. Wipe all painted areas with Q²M Prep so the wheel is clean, degreased and dry.
  5. Wearing gloves, coat in sections, using the valve as your starting point, so product is never left on too long.
  6. Buff off with clean microfibre towels.
  7. Inspect with a light to make sure all residue is gone.

GYEON tip

While the wheels are off, detail the inner arches and coat glossy painted calipers too.

Back to contents ↑
Knowledge #

Can GYEON paint coatings be used on wheels?

Yes – but there's a coating built for the job.

You coated your car and have some coating left. Can it go on the wheels?

In short

Yes, GYEON EVO paint coatings can be used on wheels. But the best option is Q² Rim EVO – designed to withstand high temperatures, heat cycles from braking and more aggressive contamination.

The background

Q² Rim EVO is highly hydrophobic and extremely durable under heat – ideal for wheels and brake calipers. It also works well on metal engine bay parts and exhaust systems.

Q² Mohs EVO, Q² Syncro EVO, Q² One EVO and Q² Pure EVO are paint coatings for bodywork, but they also give wheels protection and chemical resistance, repel dirt and make cleaning easier – useful if you want the same protection across the car or have some left over.

What you need

Q²M IronWheelCleaner and Q²M Prep preparation

Q² Rim EVO purpose-built wheel coating

Step by step

  1. Clean the wheels thoroughly with Q²M IronWheelCleaner.
  2. Degrease with Q²M Prep.
  3. Coat in sections and buff off.

GYEON tip

For maximum durability on wheels and calipers, choose Q² Rim EVO.

Back to contents ↑
Knowledge #

How to clean tyres – and make your dressing last longer

How to clean tyres – and make your dressing last longer

A clean tyre makes your dressing last longer. The trick: scrub until the foam turns white.

Tyres collect dirt, grime and old dressing like every other surface. And a dirty tyre won't let your dressing bond.

In short

Scrub with Q²M TireCleaner and Q²M TireBrush. The foam turns brown as dirt breaks down – rinse and repeat until it stays white. Then your dressing will bond and last longer.

What you need

A medium-to-stiff detailing brush for the lettering

Step by step

  1. Apply an even coat of Q²M TireCleaner to the tyre.
  2. Scrub the whole tyre with Q²M TireBrush – the foam turns brown as dirt breaks down.
  3. Rinse away the dirty foam.
  4. Repeat until the foam stays white – that means the tyre is properly clean.
  5. Dry and apply your dressing or coating.

GYEON tip

Clean tyres before every dressing – it's the single biggest factor in how long the dressing lasts.

Back to contents ↑
Knowledge #

How to coat your tyres

A tyre coating outlasts any dressing – if the tyre is properly prepared.

A tyre coating lasts far longer than a dressing – but only if it can bond to clean, dry rubber.

In short

Clean the sidewalls with Q²M TireCleaner and Q²M TireBrush until the suds are white, dry completely, then apply Q² Tire with a microfibre applicator and let it cure 24 hours.

What you need

An air blower (optional), a heat gun or hairdryer

Step by step

  1. Apply Q²M TireCleaner to the sidewalls and scrub with Q²M TireBrush.
  2. Rinse and repeat until you only get clean, white suds.
  3. Dry the tyres completely – an air blower helps.
  4. Optional: carefully warm the sidewalls with a heat gun or hairdryer so the coating soaks into the rubber better.
  5. Put a generous amount of Q² Tire on the applicator, dab it around the sidewall, then wipe around, letting it soak in.
  6. Leave to dry fully for 24 hours before use.

GYEON tip

Warming the rubber increases durability – just keep the heat moving.

Back to contents ↑
Knowledge #

How to clean and protect wheel arches

Arches collect more road dirt than any other area. Here's how to deep clean and protect them.

Wheel arches take a pounding from road dirt and grime. Cleaning and protecting them properly makes every future wash easier.

In short

With the wheel off, soak the arch with Q²M APC, clean the caliper with Q²M Iron, agitate, rinse, remove tar with Q²M Tar, protect with Q²M WetCoat, then coat plastic liners with Q² Trim EVO. Maintain with Q²M Preserve.

What you need

Jack, axle stands, wheel arch brushes and mitts, an air blower

Step by step

  1. If safe, jack up one corner, remove the wheel and support the car on an axle stand. Work on one arch at a time.
  2. On the dry arch, apply Q²M APC liberally. For heavy soiling you can use it undiluted – but keep it off paint and delicate areas.
  3. Spray Q²M Iron on the caliper and let it work 1–2 minutes.
  4. Agitate the APC across the arch and suspension with arch brushes and mitts, then clean the caliper. Rinse the whole arch.
  5. Spray Q²M Iron on the arch to break down remaining build-up (and again on the caliper). Leave 1–2 minutes, rinse.
  6. Spray Q²M Tar on tar deposits, leave 1–2 minutes, agitate and rinse.
  7. Spray Q²M WetCoat over the arch and suspension and rinse immediately.
  8. For maximum protection: dry the arches fully (air blower) and apply Q² Trim EVO to hard plastics with a Q²M MF Applicator.
  9. Maintenance: after each arch wash, spray Q²M Preserve – an air blower spreads it into intricate areas.

GYEON tip

Always use axle stands – never work under a car supported only by a jack.

Back to contents ↑
Real-life fix #

Tarnished chrome trim? How to bring back the shine

Dull chrome? Start gentle and step up only if needed.

Fallout and water spotting slowly take their toll on your metal trim.

In short

Least aggressive first: a hot wash with a degreaser, then Q²M WaterSpot for stubborn spots, then Q²M MetalPolish for dull or heavily spotted trim.

What you need

Clean microfibre towels

Step by step

  1. Make sure the trim is clean and dry.
  2. Mild water spotting: a hot wash with a degreaser may be enough.
  3. Still visible? Soak a clean microfibre with Q²M WaterSpot, apply to the trim and let it work. Wipe off the residue with Q²M Prep on a separate towel.
  4. Still spotted or dull? Put a couple of dabs of Q²M MetalPolish on a Q²M MF Applicator, apply lightly in straight lines and buff off with a clean microfibre.

GYEON tip

Q²M MetalPolish not only removes staining – it revives the trim to a factory finish.

Back to contents ↑
Knowledge #

How to clean and polish exhaust tailpipes

Sooty tailpipes ruin a clean car. Five minutes with a metal polish fixes it.

A clean car with black, sooty tailpipes still looks unfinished.

In short

Wash the tailpipes to remove loose carbon, then work in Q²M MetalPolish with a microfibre and buff off. Repeat until clean and shiny.

What you need

Clean microfibre towels

Step by step

  1. Wash the tailpipes and remove loose carbon deposits.
  2. Once dry, apply Q²M MetalPolish to a microfibre and work it into the tailpipe.
  3. Buff off with a clean microfibre.
  4. Repeat if needed.

GYEON tip

Protect them afterwards with Q² CanCoat EVO or Q² Rim EVO – it handles heat and makes the next clean easier.

Back to contents ↑
Chapter 07

Glass & visibility

Clean, coated glass is a safety feature. Clean it without streaks, choose the right glass product and keep rain, fog and wiper judder under control.

Glass & visibility
Knowledge #

How to clean your car windows without streaks

Probably the most hated job in car care. Here is our technique for crystal-clear windows every time.

Probably the most hated thing to do by everyone! Streaks show up the moment the sun hits the glass. With the right technique and two towels, crystal-clear windows take just a few minutes after your weekly wash.

In short

Spray the glass cleaner onto a short-pile microfibre (never onto the glass), wipe, and finish with a waffle-weave towel. Finish vertically outside and horizontally inside, so you instantly see which side a streak is on.

What you need

Q²M Prep first wipe for heavily contaminated glass (e.g. smoke film)

Q²M Glass high-quality glass cleaner

A short-pile microfibre towel

A waffle-weave microfibre towel

Step by step

  1. Exterior: spray Q²M Glass onto the short-pile microfibre – not directly on the glass, and don't overuse it.
  2. Wipe the glass, then finish with the waffle towel in vertical motions until streak-free.
  3. Interior: repeat with the same towels, but finish in horizontal motions.
  4. Heavy contamination (smoke deposits): do a first wipe with Q²M Prep, then finish with Q²M Glass.

GYEON tip

Finishing in a different direction inside and outside tells you immediately whether a remaining streak is on the inside or the outside.

Back to contents ↑
Product guide #

View EVO, QuickView, Glass+ or AntiFog: which glass product do you need?

Four glass products, four jobs. Here's which one you need.

Clear glass is a safety feature. GYEON has four glass products – and they solve different problems.

In short

Q² View EVO: durable windscreen coating, up to 24 months. Q² QuickView: quick rain repellent in minutes, up to 6 months. Q²M Glass+: hydrophobic glass cleaner for maintenance. Q² AntiFog: stops the inside of your glass fogging, at least 2 months.

In detail

Q² VIEW EVO – LONG-LASTING RAIN REPELLENT
  • Up to 24 months / 50,000 km; water starts beading off from around 50 km/h.
  • Kit: Q² Repel EVO, Q²M GlassPolish, applicator set.
  • Apply at least one layer – there's no maximum, and more layers mean more durability.
  • For windscreens and exterior glass.
Q² QUICKVIEW – RAIN REPELLENT IN MINUTES
  • Squeeze, spread to a dry, cloudy film, let cure 5–20 minutes, wipe off with a damp microfibre.
  • Up to 6 months. Can be used on top of an existing glass coating as a refresh.
Q²M GLASS+ – THE CLEANER THAT ADDS REPELLENCY
  • Removes dirt, fingerprints and oily film and leaves a light water-repellent layer.
  • Inside and outside; safe on coated glass. Temporary repellency – not a coating.
Q² ANTIFOG – FOR THE INSIDE
  • Interior glass coating against fog and condensation.
  • At least 2 months.
ALSO

How to choose

Quick chooser:
  1. Want the longest protection → Q² View EVO.
  2. Want rain repellency today, in 10 minutes → Q² QuickView.
  3. Want to keep any coating working while you clean → Q²M Glass+.
  4. Windows fog up inside → Q² AntiFog.

GYEON tip

Coat the wiper blades when you coat the windscreen – it helps prevent judder.

Back to contents ↑
Complete guide #

Windscreen protection: coat it and keep it working

A coated windscreen is a real safety gain. Here's how to apply it properly and make it last.

A protected windscreen is a real safety gain, especially in winter: rain rolls off, dirt sticks less, and visibility improves. Here's how to apply a durable glass coating – and how to keep it working.

In short

Clay the glass, polish it with Q²M GlassPolish, apply Q² Repel EVO – at least one layer, more layers for more durability – coat the wiper blades and buff off. Then clean regularly, top up with Q²M Glass+ and never wipe a dry screen.

Guide

1. PREPARE THE GLASS
  • Clay the glass with plenty of clay lubricant to remove bonded contamination. Wipe off the lubricant with a clean microfibre.
  • Mask rubber and plastic trim around the glass so the cleansing polish can't stain it.
  • Polish the glass with Q²M GlassPolish (included in the kit) by hand or with a polisher and felt pad if you are confident. It cleans the glass and prepares it so the coating bonds. Leave 15–20 minutes, then wipe off with a clean, damp microfibre.
2. APPLY THE COATING
  • Wrap the larger block in a suede cloth, load it with Q² Repel EVO and work it into the glass in circular motions until the suede squeaks.
  • Apply at least one layer. There is no maximum – every extra layer adds durability. Wait about 20 minutes between layers.
  • Leave 20 minutes, then buff off with a clean Q²M BaldWipe.
3. COAT THE WIPER BLADES

While the first layer sits: clean the blades with APC or Q²M TireCleaner, then apply Q² Repel EVO to both sides of each blade with the suede. Coated glass with uncoated blades is a common cause of judder.

4. KEEP IT WORKING: 5 HABITS
  • Clean regularly – built-up dirt speeds up wear of the coating.
  • Clean and top up with Q²M Glass+: it removes dirt while maintaining the hydrophobic effect.
  • Never use the wipers on a dry screen.
  • Keep the wiper blades coated.
  • Use plenty of screen wash when wiping a dirty screen while driving.

What you need

Q²M TireCleaner or Q²M APC wiper blades

Q²M Glass+ maintenance

Masking tape

GYEON tip

No time for the full kit? Q² QuickView gives rain repellency in minutes – see Prepare for rain.

Back to contents ↑
Real-life fix #

Wipers jumping on the windscreen? How to fix wiper judder

Juddering wipers are annoying and noisy. It all comes down to friction – here is how to bring it down.

Wiper judder is when your wipers shake, jump or judder as they move over the windscreen. The rubber sticks to the glass while the arm keeps moving, so the blade jumps instead of gliding.

In short

Judder happens when friction between rubber and glass is higher than the force of the wiper arm. Lower the friction: clean the glass, clean the blades, coat the blades and always use enough water or screen wash.

The background

The usual causes:
  • Brand-new wipers
  • A fresh rain repellent coating on the glass (uncoated blades)
  • Very dirty glass
  • Not enough water on the glass

What you need

Q² View EVO (rain repellent kit) also used to coat the wiper blades

Q²M TireCleaner or an APC to clean the wiper blades

Q²M Glass to clean the glass

A microfibre towel

Step by step

  1. Clean the glass thoroughly.
  2. Clean the wiper blades with a microfibre and Q²M TireCleaner or APC.
  3. If your glass is coated, coat the wiper blades too, using the same rain repellent.
  4. Never use the wipers on a dry screen – always use plenty of screen wash.

GYEON tip

When you coat your windscreen, always coat the blades as well. It reduces judder and protects the coating.

Back to contents ↑
Real-life fix #

Prepare for rain: clear visibility in every season

Prepare for rain: clear visibility in every season

Rain, drizzle and fog mean worse visibility. Ten minutes with a rain repellent makes every rainy drive safer.

Spring showers, autumn drizzle, fog and less sunshine all mean reduced visibility and tougher driving conditions. Having a protected paintwork is nice – having an undisrupted clear view is best.

In short

Clean and prep the glass, apply Q² QuickView in circular motions, let it sit and wipe off. Maintain with Q²M Glass+, which also boosts any existing rain repellent.

The background

Q² QuickView is an ultra-slick rain repellent: water and dirt roll off, improving visibility – even without using the wipers. The built-in felt applicator makes it quick and mess-free, and one application lasts up to six months.

What you need

Q² QuickView rain repellent with built-in applicator

Q²M Clay Bar removes bonded particles

Q²M Prep ensures proper bonding

Q²M Glass+ cleaner and hydrophobic booster for maintenance

Q²M BaldWipe to wipe off

Step by step

  1. Prep the glass: make sure it is clean and decontaminated. Use Q²M Clay Bar for bonded particles, then wipe with Q²M Prep.
  2. Apply Q² QuickView section by section in circular motions to work it into the pores of the glass, finishing in straight lines.
  3. Let it dry for at least 5 minutes (up to 30 minutes makes the wipe-off even easier).
  4. Wipe off with a damp Q²M BaldWipe, then give a final wipe with a clean, dry towel.
  5. Maintain: one or two sprays of Q²M Glass+ on a glass towel, work over the surface until a slight haze, then remove with a clean, dry short-nap towel.

GYEON tip

Q²M Glass+ can be used over any existing rain repellent and works as a hydrophobic booster – inside and outside, it also leaves an anti-static surface.

Back to contents ↑
Real-life fix #

Foggy windows in the morning? How to keep the inside of your glass clear

Foggy glass is annoying – and dangerous. Why it happens, and how Q² AntiFog keeps your view clear all season.

Clear exterior glass doesn't help much if the inside fogs up every morning. Foggy windows are not only annoying – a clear view is crucial for your safety.

In short

Clean the inside of the glass, wipe it with Q²M Prep, then apply Q² AntiFog with the applicator and buff to a clear finish.

The background

Moisture inside the car is the cause. Getting in during a heavy downpour, carpets or seats that were shampooed and are not fully dry, or a windscreen that was not sealed correctly after replacement – all increase humidity inside the cabin.

What you need

Q²M Glass to clean the glass first

A clean microfibre towel

Step by step

  1. Start with spotless glass: clean the inside of the windows.
  2. Give a final wipe with Q²M Prep and let it sit about 30 minutes before applying.
  3. Apply Q² AntiFog with the applicator in circular motions, making sure the coverage is even.
  4. Buff off with a clean microfibre towel to a clear finish.

GYEON tip

Good to know: Q² AntiFog keeps the glass clear, but it does not fix the cause. If the fogging comes from a leak or a badly sealed windscreen, find the source and fix it.

Back to contents ↑
Chapter 08

Interior

You spend all your driving time inside the car. From a full deep clean to everyday hygiene, leather, Alcantara, textiles and screens – here is how to care for every interior surface.

Interior
Knowledge #

Deep interior detailing: the complete step-by-step guide

A full interior detail is all about order. Follow these steps and your interior will be as good as new.

A deep interior clean is not hard – it is all about the right order. Work methodically and you will never clean the same area twice.

In short

Empty the car, vacuum from the back to the front, clean trim, then dashboard and contact points, then seats and carpets, protect the plastics and finish with the glass.

What you need

Q²M TrimCleaner or diluted Q²M APC plastic trim

Q²M InteriorDetailer dashboard and contact points

Q²M FabricCleaner stubborn stains

Q²M Glass and Q²M BaldWipe glass and piano black

Q²M Preserve protection for plastic trim

Interior brushes, vacuum, a trim tool or cocktail stick (steam cleaner optional)

Step by step

  1. Assess the interior and plan your approach. Remove all items from the car.
  2. Start at the back with the boot. Brush and vacuum all loose debris, including tool compartments and false floors.
  3. Work forward: fold seats and armrests, slide seats on their rails to reach under and between them, then the footwells and pedals. Finish with seats, door bins and glovebox.
  4. Go back to the start and clean all plastic trim with Q²M TrimCleaner or diluted APC and a brush. Rinse the brush regularly in clean water.
  5. Dashboard and driver's area: use Q²M InteriorDetailer, with extra attention to contact points. A trim tool or cocktail stick gets into tight spaces.
  6. Seats and carpets: steam if you have a steamer, wiping as you go. Treat stubborn stains with Q²M FabricCleaner and a brush.
  7. Protect and enhance plastic trim with Q²M Preserve.
  8. Clean all interior glass and piano black trim with Q²M Glass and Q²M BaldWipes.
  9. Final inspection.

GYEON tip

Working outside on a windy day? Start on the side the wind is coming from – otherwise opening the other doors blows dust back onto the side you just cleaned.

Back to contents ↑
Knowledge #

5 most common mistakes when detailing your interior

Five small mistakes that make interior cleaning harder – or even cause damage.

We all made these mistakes at least once. Avoid them and your interior detail will be faster and safer.

In short

Spray onto the towel not the surface, use microfibre (not brushes) on piano black, watch your vacuum hose, work top to bottom and always use a light.

What you need

Q²M SoftWipe for piano black and screens

An inspection light

Step by step

  1. Don't spray directly onto interior surfaces – it creates overspray. Spray onto a clean microfibre, then apply.
  2. Don't use brushes on high-gloss areas like piano black, even soft ones. Use a high-quality soft microfibre.
  3. Watch the vacuum hose: it easily scratches paint and trim. Cover the risk areas or pinch the hose between your legs so it doesn't drag over the sills.
  4. Work from the top down – otherwise dirt falls onto the areas you have just cleaned.
  5. Always use a light. Dark interiors and privacy glass hide a lot, e.g. under the seats.

GYEON tip

Keep separate towels for glass, piano black and general trim – it is the easiest way to avoid scratches and streaks.

Back to contents ↑
Complete guide #

Clean, fresh and hygienic interior: daily care

Clean, fresh and hygienic interior: daily care

A few minutes a week keeps your interior feeling new. Here's the routine.

You touch the same few points in your car every day – steering wheel, gear knob, door handles, buttons. A quick routine keeps them clean and your interior feeling fresh between deep cleans.

In short

Spray Q²M InteriorDetailer onto a clean microfibre and wipe all contact points once a week – it removes 99.9% of bacteria. For longer-lasting hygiene, protect surfaces with Q² Purify Coat and maintain with Q²M Purify Maintain.

Guide

1. WHAT Q²M INTERIORDETAILER DOES

An alcohol-based (60%) quick interior cleaner that removes the majority of organic contaminants – and 99.9% of bacteria on interior surfaces, as tested and confirmed by two independent Korean test institutes, KTR and KOTITI. It's safe on leather, plastic, Alcantara, textiles, glass and all interior trim – and perfect for daily use.

It doesn't replace dedicated cleaners like Q²M TrimCleaner or Q²M LeatherCleaner – it complements them between deep cleans.

2. THE CONTACT-POINT ROUTINE
  • Spray Q²M InteriorDetailer onto a clean Q²M BaldWipe – not directly onto screens or buttons.
  • Wipe the steering wheel, gear knob, handbrake, door handles, buttons, armrests and seat belt buckles.
  • Use a fresh side of the towel as you go.
  • A few minutes each week is enough.
3. LONGER-LASTING HYGIENE: THE PURIFY RANGE
4. WHEN TO GO FURTHER

What you need

Q²M TrimCleaner , Q²M LeatherCleaner, Q²M FabricCleaner deeper cleaning

Q² Purify Coat and Q²M Purify Maintain longer-lasting hygiene

Q²M OdorRemover odours

GYEON tip

Keep a bottle and a dedicated towel in the door pocket – it turns into a habit.

Back to contents ↑
Knowledge #

How to clean and protect your car's textiles

Cars mix several textiles, each with its own approach. Clean them right, then protect them all.

Today's cars combine different textiles – carpets, fabric seats, Alcantara – and each needs a slightly different approach to clean and protect.

In short

Vacuum, clean with a fabric cleaner (light mist first), let dry fully, then protect with two layers of Q² FabricCoat worked into the fibres.

What you need

Interior brush, gloves, light-coloured microfibre towels

Coating applicator (for Alcantara)

Vacuum; wet vac or steamer optional

Step by step

Carpets:
  1. Vacuum thoroughly, then inspect.
  2. Start with a light mist of Q²M FabricCleaner and brush. Spray more and agitate further only if needed. A steamer or wet vac helps with stubborn dirt.
  3. No wet vac? Remove residue with light-coloured microfibres. Let dry fully.
Alcantara:
  1. Vacuum, then spray FabricCleaner onto a microfibre (not the fabric) and gently work it in. For more dirt, apply a little cleaner to the brush bristles and work in circular motions. Let dry fully.
Protection:
  1. Take out the mats and brush the fibres in one direction. Apply Q² FabricCoat and, wearing gloves, wipe it into the fibres in the same direction.
  2. Brush the opposite way and apply again for full coverage.
  3. Leave 15–20 minutes and repeat for maximum protection.
  4. Let everything dry fully before use.

GYEON tip

On Alcantara, apply Q² FabricCoat with a coating applicator instead of spraying – no overspray on the rest of the interior. Then massage it in with gloves.

Back to contents ↑
Knowledge #

How to clean car carpets and floor mats

A vacuum alone rarely gets carpets really clean. A simple trick, the right cleaner and a protectant make all the difference.

Floor mats and carpets trap dust, dirt and grime deep in their fibres – sometimes too deep for a simple vacuum cleaner.

In short

Lift the fibres first (latex gloves and a bit of static do wonders), vacuum, clean with a fabric cleaner, let dry completely and protect with a fabric coating.

What you need

Q² FabricCoat fabric protectant

Latex gloves

A brush and a light-coloured microfibre towel

Vacuum (extraction vacuum for heavy dirt)

Step by step

  1. Lift the fibres: wearing latex gloves, rub the surface gently until the fibres are charged with static. Most of the bits will lift upwards.
  2. Vacuum thoroughly.
  3. Light grime: spray Q²M FabricCleaner lightly and remove the excess with a light-coloured microfibre – you will see the dirt come off.
  4. Heavy dirt: spray more generously, brush the surface and, for the best result, use an extraction vacuum.
  5. Only put the mats back in the car when they are fully dry.
  6. Protect with Q² FabricCoat – it creates a barrier against water and dirt and makes future cleaning easier.

GYEON tip

A light-coloured microfibre shows you exactly how much dirt is coming out – stop when the towel stays clean.

Back to contents ↑
Real-life fix #

Spilled a drink on your car seat? How to clean it without a water mark

The mistake most people make is cleaning only the stain – and ending up with a bigger water mark. Here is the right way.

Coffee, juice, water – liquid spills will leave a water mark, especially on light upholstery. The most common mistake is cleaning only the stain: once it dries, you are left with an even bigger mark.

In short

Always treat the whole seat section (the base or the backrest), not only the spill. Apply Q²M FabricCleaner with a brush, work evenly, then extract or wipe and let it dry.

What you need

Q²M LeatherBrush soft, and it limits overspray

Step by step

  1. Spray onto the brush, not the seat: mist Q²M LeatherBrush several times with Q²M FabricCleaner.
  2. Start with the stain and work the brush over it until it is gone.
  3. Continue over the whole section – the entire base or backrest, or section by section between the stitching.
  4. Remove the excess with a wet vac, or wipe down with a clean Q²M BaldWipe.
  5. Let it dry fully and check that the stain is gone.

GYEON tip

Once the seats are clean, protect them with Q² FabricCoat so the next spill beads up instead of soaking in.

Back to contents ↑
Real-life fix #

Pet hair in your car? How to remove it in minutes

Pet hair in your car? How to remove it in minutes

Dog hair weaves itself into fabric and a vacuum alone struggles. A pair of rubber gloves changes everything.

Dog hair in the car can be a real pain – the hairs get stuck in the fibres and are very difficult to remove with a vacuum cleaner alone. This hack works on your car upholstery and on your sofa at home.

In short

Vacuum first, then use friction: wipe the fabric with rubber or nitrile gloves (or a rubber brush) to roll the hair into a ball, and vacuum again.

What you need

Q²M FabricCleaner to freshen up the fabric afterwards

Rubber or nitrile gloves, or a rubber brush

A vacuum cleaner

Step by step

  1. Vacuum to remove most of the debris and surface hair.
  2. Put on rubber or nitrile gloves. With your hand arched, stroke the fabric towards you with the edge of your hand and little finger, piling the hair into a ball.
  3. Vacuum again to pick up the compacted hair.
  4. Never use sharp or porous objects – they can permanently change the look and shape of the fibres.

GYEON tip

Protect the seats afterwards with Q² FabricCoat – hair and dirt cling less to protected fabric.

Back to contents ↑
Complete guide #

Leather seat care: the complete guide

Leather lasts for years with the right care – and gets ruined fast with the wrong one. Everything in one guide.

Leather seats last for many years – if they're cleaned and protected the right way. This guide covers what kind of leather you have, how to clean it, what to avoid and how to protect it.

In short

Identify your leather, vacuum, clean section by section with Q²M LeatherCleaner and a soft brush (Natural first), wipe off with three towels, then protect with Q² LeatherShield EVO (new leather) or Q² LeatherCoat (older leather).

Guide

1. WHAT KIND OF LEATHER DO YOU HAVE?
  • PU / faux leather – also called leatherette, pleather, PVC or artificial leather. Common in regular-priced cars.
  • Cork leather – rare, used in custom interiors.
  • Real leather – usually cow hide. It rarely keeps its natural colour: it's painted and coated.
  • Classic cars often have very absorbent Connolly leather that needs extra care.

How to tell: if the back of the material looks like woven fabric, it's probably not natural leather – but some manufacturers back real leather with fabric too, so a professional is often needed to be sure.

2. ASSESS BEFORE YOU CLEAN

Inspect for wear or damage such as cracks or tears. The age and type of leather decide how gentle you need to be.

3. HOW TO CLEAN IT
  • Vacuum first. Gently stretch the leather to open the seams and recline the seat for better access.
  • Clean in sections with Q²M LeatherCleaner and Q²M LeatherBrush in circular motions. Always start with Q²M LeatherCleaner Natural; use Strong only if needed.
  • Use a foam pump applicator to avoid overspray and stop liquid seeping into perforated leather.
  • Rinse your brush regularly in a bucket of clean water.
  • Wipe off with a clean, dry, light-coloured microfibre – you'll see the dirt come off. Then a damp towel to remove all residue, then a third dry towel.
  • On the steering wheel, cover the instruments with a spare towel.
4. THE 5 WORST THINGS YOU CAN DO
  • Being aggressive – scrubbing hard marks the coating; heat (e.g. steamers) can change the leather's shape and fit.
  • Wrong tools – no stiff drill brushes; use a soft horsehair hand brush.
  • Wrong chemicals – harsh products can permanently damage the surface.
  • Ignoring clothes and pockets – keys, tools and denim studs scratch and tear leather.
  • Neglect – dirt builds up evenly so you don't notice it until it stains. Build leather care into your regular wash.
5. PROTECT IT
  • Q² LeatherShield EVO – a true SiO₂ product for new or modern leather.
  • Q² LeatherCoat – more of a sealant, preferred for older or worn leather; can be re-applied several times a year.

Apply one seat at a time with the supplied applicator, smooth and with light, consistent pressure. After a few minutes, wipe down with a clean microfibre. Use an inspection lamp to check full coverage and avoid high spots.

Tip for steering wheels: some protection can make the surface slippery – be careful.

What you need

Q²M LeatherSet Natural cleaner, coat, brush and applicator in one

Light-coloured microfibre towels, foam pump applicator, inspection lamp

GYEON tip

Little and often: a light clean every few weeks takes minutes and stops stains before they set.

Back to contents ↑
Knowledge #

How to protect leather upholstery: LeatherShield or LeatherCoat?

Two leather protections, two different jobs. Which one fits your seats – and how to apply it.

Clean leather deserves protection. GYEON offers two – and the right one depends on your leather.

In short

Q² LeatherShield EVO is a true SiO₂ product for new or modern leather. Q² LeatherCoat is more of a sealant, preferred for older or worn leather, and can be re-applied several times a year.

What you need

The supplied applicators

A clean microfibre towel

An inspection lamp

Step by step

  1. Start with clean, dry leather.
  2. Work one seat at a time with the supplied applicator.
  3. Use a smooth motion with consistent light pressure for an even layer.
  4. Check with an inspection lamp that you have full coverage.
  5. After a few minutes, give a final wipe-down with a clean microfibre.
  6. Check again with the lamp for any residue to avoid high spots.

GYEON tip

Interiors are dark – an inspection lamp is your best friend for even coverage and no high spots.

Back to contents ↑
Knowledge #

How to clean contrast stitching in leather seats

White or coloured stitching shows every bit of dirt. A weak APC dilution and a soft brush bring it back.

Contrast stitching looks great – until it turns grey. The good news: one of the key benefits of Q²M APC is that you can vary the dilution to suit the job.

In short

Start with a very weak dilution of Q²M APC (1:15 to 1:20), spray it onto a soft leather brush, work it gently into the stitching and wipe off immediately.

What you need

Q²M APC diluted 1:15 to 1:20

Step by step

  1. Always do a small patch test first, ideally on a hidden area.
  2. Dilute Q²M APC 1:15 to 1:20.
  3. Spray it onto the Q²M LeatherBrush, not onto the seat.
  4. Gently work the brush into the stitching.
  5. Immediately wipe off with a clean Q²M BaldWipe. Repeat if necessary.

GYEON tip

Protect the leather and stitching afterwards with a leather coating – dirt has a harder time settling in.

Back to contents ↑
Real-life fix #

Autumn is here: protect your leather interior

Wet weather means dirt carried into the car – and your leather seats take it first. Two simple steps keep them clean all season.

Autumn brings rain and dirt – and you carry some of that mess into the car every time you get in and out. The first victim: your leather upholstery.

In short

Vacuum, clean with Q²M LeatherCleaner Natural and the LeatherBrush, then protect with Q² LeatherCoat. Everything you need is in Q²M LeatherSet Natural.

The background

Q²M LeatherSet Natural contains Q²M LeatherCleaner Natural, Q² LeatherCoat, the LeatherBrush and an MF Applicator. LeatherCleaner Natural removes light dirt and oily residue and leaves a fully matte finish on all modern leather. LeatherCoat gives long-lasting protection and makes future maintenance easier.

What you need

A vacuum

Microfibre towels

Step by step

  1. Vacuum the seats to remove sand and loose dirt.
  2. Apply some foam of Q²M LeatherCleaner onto the LeatherBrush and use circular motions to lift the dirt.
  3. Wipe the dirt away with a microfibre towel in straight motions.
  4. Apply a small amount of Q² LeatherCoat onto the MF Applicator and work in small sections.
  5. Wipe with a clean microfibre towel so no residue is left.

GYEON tip

Protected leather stays clean longer – the next wipe-down takes half the time.

Back to contents ↑
Real-life fix #

Why does my steering wheel get shiny – and how to stop it

That shine isn't polish – it's skin oil and dirt. Here is how to bring the factory matt finish back.

It is a very common issue, especially on leather wheels. The original matt finish slowly turns shiny and feels slippery.

In short

The shine comes from the natural oils of your hands and fine dirt that polishes the surface over time. Clean regularly with Q²M LeatherCleaner and drive with clean hands.

The background

Natural oils from your palms transfer to the wheel every time you drive and build up over time. Any dirt on your hands acts as an abrasive and literally polishes the surface. The result: shine instead of the original matt finish, and less grip.

What you need

Q²M LeatherCleaner

Step by step

  1. Apply Q²M LeatherCleaner to the Q²M LeatherBrush.
  2. Gently clean the steering wheel section by section.
  3. Wipe off with a clean Q²M BaldWipe.
  4. Repeat regularly to stop oils building up again.
  5. Drive with clean hands.

GYEON tip

You can protect the leather afterwards, but be careful: some protection can make the surface slippery – not what you want on a steering wheel.

Back to contents ↑
Complete guide #

Alcantara: what it is and how to clean and protect it

The race-car material that feels amazing when new – and ages fast without care. The complete guide.

You'll find it on steering wheels, seats and headliners of sporty cars. Alcantara feels amazing when new – but it ages quickly without the right care.

In short

Alcantara is a durable synthetic material. Clean it gently with Q²M FabricCleaner applied to a microfibre, lift the fibres with a soft brush and vacuum, and protect it with Q² FabricCoat.

Guide

1. WHAT IS ALCANTARA?

A synthetic material invented in Japan in the 1970s and made in Italy by the company Alcantara. It became the go-to upholstery for race cars and was soon adopted by car makers for their sporty models. It's more durable than suede, grips better than leather and doesn't absorb heat like natural materials.

2. WHY IT GETS MATTED

Oily or dirty hands – especially on steering wheels – and the wrong cleaning compress the fibres. The goal of every step is to lift the fibres, never to press them down.

3. HOW TO CLEAN IT
  • Apply Q²M FabricCleaner onto a clean Q²M BaldWipe – never spray directly on the Alcantara.
  • Wipe gently to work the cleaner into the fibres and release the dirt.
  • Switch to a separate clean microfibre to wipe the dirt away.
  • Stubborn dirt: use a long-bristle brush to work the cleaner to the base of the fibres.
  • When no more dirt comes out, vacuum with a soft brush attachment to lift the fibres. Avoid direct contact with the nozzle – it can mark the fabric.
4. HOW TO PROTECT IT
  • Make sure it's clean and completely dry.
  • Cover the surrounding trim.
  • Spray Q² FabricCoat evenly – or, to avoid overspray (e.g. on a steering wheel), apply it with a coating applicator.
  • Wearing rubber or nitrile gloves, massage the coating into the fibres – this increases durability.
  • Let it dry thoroughly.
5. MAINTENANCE

Vacuum regularly with a soft brush attachment to lift dust and revive the fibres. And drive with clean hands.

What you need

A long-bristle brush, nitrile gloves, a vacuum with soft brush attachment

GYEON tip

Protect a new Alcantara steering wheel from day one – prevention is much easier than reviving matted fibres.

Back to contents ↑
Real-life fix #

How to remove light scratches from hard plastic trim

Light scratches in hard plastic trim can often be removed with nothing but heat.

Light scratches on unpainted plastic trim are annoying – and they can often be removed with careful heat.

In short

On clean trim, use a heat gun on its lowest setting about 15 cm away, keep it moving in circles and watch the light scratches fade. Let it cool without touching.

What you need

Q²M TrimCleaner or Q²M APC to clean the trim first

Q² Trim EVO to protect afterwards

A heat gun

Step by step

  1. Clean the area thoroughly.
  2. Set the heat gun to the lowest setting and hold it about 15 cm away.
  3. Keep it moving in a circular motion – never focus on one spot or hold it too close, or you will burn the plastic.
  4. Watch the light scratches gradually disappear.
  5. Don't touch the trim – let it cool.

GYEON tip

Once it has cooled, protect the trim with Q² Trim EVO to keep it dark and protected.

Back to contents ↑
Knowledge #

How to safely clean your car's touchscreen

Touchscreens get dirty fast and scratch easily. A soft towel and the right technique keep them clear.

Infotainment screens get dirty quickly, especially touchscreens. Their surface is soft and scratches easily, so they need gentle treatment.

In short

Remove loose dust without contact, then wipe gently with Q²M Glass sprayed onto a clean Q²M SoftWipe – never directly on the screen.

What you need

Q²M SoftWipe soft, edgeless microfibre

An air blower or hairdryer (cold setting)

Step by step

  1. Blow away loose dust with an air blower or hairdryer – no contact, no scratches.
  2. Spray Q²M Glass onto a clean Q²M SoftWipe. Never spray onto the screen.
  3. Wipe the screen lightly.
  4. Flip the towel and wipe again to remove any residue.

GYEON tip

Keep a dedicated SoftWipe for screens only, so it never picks up grit from other surfaces.

Back to contents ↑
Real-life fix #

How to clean and protect a fabric soft top

Good weather is coming – the right time to clean and protect your convertible roof.

When the good season comes, it is the right time to clean and protect your fabric soft top. Protecting it is not complicated – as always in detailing, the preparation is the hardest part.

In short

Clean the roof, let it dry completely, mask off the surrounding paint, then apply two thin layers of fabric protectant and keep it dry for 24 hours.

What you need

Q²M FabricCleaner to clean the roof first

Q² FabricCoat fabric protectant

Plastic foil and masking tape

Step by step

  1. Clean the roof thoroughly (see How to clean car carpets and floor mats) and let it dry completely.
  2. Mask off the surrounding area with tape and plastic foil – the protectant must not get on the paint or other surfaces.
  3. Spray a thin layer of Q² FabricCoat over the fabric.
  4. Work it in with a glove or Q²M LeatherBrush.
  5. Let it dry for the time on the label – warm air or infrared speeds this up.
  6. Apply a second layer the same way.
  7. Keep the roof dry for at least 24 hours.

GYEON tip

The same method works for every type of fabric in and on your car.

Back to contents ↑
Knowledge #

How to make your car interior feel fresh and inviting

How to make your car interior feel fresh and inviting

Cleanliness and scent make the atmosphere. Here is how to make your cabin a nicer place to be.

You spend hours in your car. To improve the mood inside, focus on two things: cleanliness and ambiance.

In short

Clean every surface with the right product – trim, leather, fabric – keep contact points fresh with Q²M InteriorDetailer and add a pleasant fragrance with Q²M Scents.

What you need

Q²M InteriorDetailer daily cleaning and disinfecting of surfaces, with a fresh, pleasant scent

Q²M TrimCleaner gentle cleaner for plastics and vinyl

Q²M Scents high-quality air fresheners

Q²M FabricCleaner removes dirt and stains from fabric and upholstery

Q²M LeatherCleaner – keeps leather soft and pleasant to the touch

Step by step

  1. Clean plastics and vinyl with Q²M TrimCleaner.
  2. Clean leather with Q²M LeatherCleaner, or fabric with Q²M FabricCleaner – stains and lingering odours disappear.
  3. Wipe the contact points with Q²M InteriorDetailer.
  4. Finish with Q²M Scents for a pleasant fragrance.

GYEON tip

Clean first, then scent – a fragrance works best in a cabin that is already fresh.

Back to contents ↑
Real-life fix #

Selling your car? How to prepare the interior

Dirty cockpits and strong smells put buyers off immediately. Make the interior look, smell and feel clean.

With the exterior done (see part 1), it's time for the interior. This is where the next owner will spend most of their time – a dirty cockpit or a strong smell puts buyers off immediately. It needs to look clean, smell clean and feel clean.

In short

Empty the car, vacuum everything, clean the trim, fabric and leather – with extra attention to the steering wheel and gear knob – and let the car air out.

What you need

Q²M TrimCleaner or Q²M APC (weak dilution) trim

Q²M LeatherCleaner and Q²M LeatherBrush leather

Q²M FabricCleaner fabric

Interior brush, clean microfibre towels, vacuum with attachments

Step by step

  1. Remove all loose and personal items, including mats.
  2. Vacuum the entire interior with the right attachments for hard-to-reach areas and different materials.
  3. Trim: clean with Q²M TrimCleaner or a weak Q²M APC solution, agitate with an interior brush in circles and wipe with a dry microfibre. Focus on door handles, gear knob, armrests and handbrake.
  4. Fabric: treat spills and stains with Q²M FabricCleaner and a shampoo vac – or a brush and microfibre. Rinse the brush regularly.
  5. Leather: clean with Q²M LeatherCleaner and Q²M LeatherBrush. A grubby steering wheel or gear knob is the last thing a buyer wants to feel.
  6. Odours: the steps above usually remove them; if not, use a dedicated odour remover.
  7. Leave the car to air and dry out thoroughly.

GYEON tip

Buyers touch the steering wheel, gear knob and door handles first – make those perfect.

Back to contents ↑
Chapter 09

PPF care

Paint protection film stops chips – but it needs the right care to stay clear and glossy. Decide between film and coating, then keep your PPF looking new for years.

PPF care
Knowledge #

Paint coating or PPF: which one do you need?

Paint coating or PPF: which one do you need?

Our certified detailers hear this question every day. Here is the honest answer.

Our certified detailers are often asked this exact question. Both offer protection – and both have pros and cons.

In short

A ceramic coating is much more affordable and protects against chemicals, dirt and UV, but can't stop stone chips like PPF. PPF offers the best physical protection but is labour-intensive and much more expensive to install.

The background

Ceramic paint coating:
  • Much more affordable
  • Gloss, slickness, easier cleaning
  • Higher scratch resistance than uncoated paint – but not stone-chip protection
Paint protection film (PPF):
  • Thick polyurethane film – the best protection against stone chips and mechanical impact
  • Very labour-intensive to apply, so a much higher installation price

Many owners combine both: PPF on the front and high-impact areas, a coating on the rest – and a coating made for film on top of the PPF.

What you need

Q² CanCoat EVO easy DIY paint coating

Q² PPF EVO coating for PPF

Find a GYEON certified detailer for professional coatings and PPF

Step by step

  1. Decide what you need: easier maintenance and gloss (coating) or impact protection (PPF).
  2. Check your budget.
  3. Consider combining both on the areas that matter most.

GYEON tip

Whatever you choose, maintenance makes it last – a coated car and a filmed car both need the right wash routine.

Back to contents ↑
Knowledge #

How to protect your car from stone chips

Only one thing really stops stone chips: a second skin.

Motorway driving, gravel roads, the car in front – stone chips happen. What is the best protection?

In short

Paint protection film (PPF). It gives your car a second skin that protects against mechanical and chemical damage, is very durable and has outstanding self-healing properties.

The background

With the right maintenance, PPF can protect your car for many years. A coating made for film keeps it hydrophobic and easier to clean.

What you need

Q²M PPF Wash and Q²M PPF Maintain maintenance

Q² PPF EVO coating for the film

GYEON PPF – installed by a certified installer

Step by step

  1. Have PPF installed by a professional (at least on the front end).
  2. Coat the film with Q² PPF EVO.
  3. Maintain with Q²M PPF Wash and Q²M PPF Maintain.

GYEON tip

Front bumper, bonnet, wings and mirrors take most of the hits – start there if you don't want a full wrap.

Back to contents ↑
Complete guide #

PPF care: from installation day to years later

PPF care: from installation day to years later

PPF protects your paint. This guide protects your PPF – from day one to years later.

Paint protection film protects your paint – but the film itself needs care too. Without it, PPF shows signs of ageing: dullness, staining, loss of slickness. Here's the full lifecycle.

In short

Let new film cure for 48 hours, coat it with Q² PPF EVO, wash with Q²M PPF Wash using soft mitts only, maintain with Q²M PPF Maintain, and when it looks tired, revive it with Q²M PPF Renew.

Guide

1. THE FIRST 48 HOURS

Let the film cure for 48 hours before exposing it to water or harsh conditions: no washing, no chemicals. This lets it bond properly to the paint.

2. COAT THE FILM

If the PPF wasn't coated, apply Q² PPF EVO once cured – a flexible ceramic coating made for film and wraps. Water, dirt and contaminants slide off more easily, it helps protect the film against fading, staining and discoloration, and it doesn't compromise the film's self-healing. Suitable for all types of PPF, including matte/stealth.

3. WASHING: Q²M PPF WASH
  • Rinse to remove loose dirt.
  • Wash with Q²M PPF Wash and a well-loaded soft mitt – it removes mild iron deposits from film and paint without claying. Use it in a bucket or as a foam.
  • Rinse, then dry with microfibre drying towels or an air blower.
  • Never use rough sponges or brushes on film.
4. MAINTAINING: Q²M PPF MAINTAIN

Spray Q²M PPF Maintain after washing and wipe off with clean microfibres (ideally Q²M SoftWipe). It keeps the film slick, SiO₂-boosted hydrophobic and protected against UV and oxidation – and also works as a drying aid. Q²M WetCoat is an alternative; re-apply Q² PPF EVO from time to time.

5. WHEN THE FILM LOOKS TIRED: Q²M PPF RENEW

PPF is a sacrificial layer – over time it shows signs of the hits it takes. When maintenance products can no longer remove them, Q²M PPF Renew – a polishing compound made for film – cleanses and rejuvenates it, improves gloss and brings back slickness.

  • Wash, decontaminate and dry.
  • Put 4–5 pea-sized dots of PPF Renew on a finishing pad (dual-action machine).
  • Work areas of about 45–60 cm square at low to medium speed, then buff off.
  • Wipe with Q²M Prep and re-protect with Q² PPF EVO.

What you need

Q² PPF EVO coating for film

Q²M PPF Renew revive tired film

GYEON tip

Maintain the film like you maintain your paint – regular care means you rarely need to polish it.

Back to contents ↑
Knowledge #

How to polish PPF and bring back its gloss

Yes, PPF can be polished. Here is when to do it and how.

PPF is a sacrificial layer: its job is to take the hits so your paint doesn't have to. Over time it shows signs of that work – and when maintenance products can no longer remove them, it is time to polish.

In short

Wash, decontaminate and dry. Polish with Q²M PPF Renew on a dual-action machine with a finishing pad, wipe with Q²M Prep and protect with Q² PPF EVO.

The background

Q²M PPF Renew cleanses and rejuvenates PPF, improves gloss and brings back that super slick finish.

What you need

Dual-action polisher and a good finishing pad

Clean microfibre towels

Step by step

  1. Wash the car thoroughly and decontaminate chemically. Dry.
  2. Put 4–5 pea-sized dots of Q²M PPF Renew on the finishing pad.
  3. Dab the product over an area of roughly 45–60 cm square.
  4. Work it in at low to medium speed, as you would when machine polishing paint.
  5. Buff off with a clean microfibre. Continue with the rest of the film.
  6. Wipe all panels with Q²M Prep.
  7. Protect with Q² PPF EVO.

GYEON tip

Use the PPF maintenance range regularly – it keeps polishing to a minimum.

Back to contents ↑
Knowledge #

Can PPF damage chrome or trim?

Short answer: not when it is applied and removed properly. Here is what to watch out for.

PPF is designed to be safe on most car surfaces, including chrome and trim – as long as it is applied correctly.

In short

Applied and removed properly, PPF does not damage chrome or trim. Problems come from poor installation, poor-quality film or incorrect removal.

The background

What can go wrong:
  • Incorrect or late removal can leave adhesive residue that is hard to remove and can damage the finish if not treated properly.
  • Poor application can trap dirt, moisture or air bubbles under the film, leading to discoloration over time.
  • On curves and edges, poor installation can cause lifting or peeling, exposing the trim to contaminants and UV.

What you need

Q²M PPF Wash and Q²M PPF Maintain regular care

A professional installer and high-quality film

Step by step

  1. Choose professional installation and high-quality film.
  2. Maintain the film regularly.
  3. Have film removed properly, not after it has aged too long.

GYEON tip

Look for a GYEON certified PPF installer near you.

Back to contents ↑
Chapter 10

Seasons & special situations

Your car's needs change with the season and with how you use it. Spring and autumn routines, summer heat, storage, road trips, track days, selling – and a few special vehicles and jobs.

Seasons & special situations
Real-life fix #

Your car after winter: what it needs

Winter leaves salt and grime everywhere – especially where you can't see it.

Winter driving exposes your car to road salt and organic contamination – and the lower half of the car takes most of it.

In short

Deep clean the wheels and arches (wheels off if possible) and protect them with Q²M WetCoat, top up your windscreen coating with Q² QuickView and clean the mats and lower door cards inside.

Step by step

  1. Remove the wheels if you can and deep clean them with Q²M IronWheelCleaner – spokes and barrels too. Protect with Q²M WetCoat.
  2. Jet wash the inner arches, then clean arches, brakes and suspension with Q²M APC. Rinse and protect with Q²M WetCoat.
  3. Top up the windscreen rain repellent with Q² QuickView.
  4. Take out all mats and boot liners. Rubber: scrub with Q²M APC and rinse. Carpet: Q²M FabricCleaner, brush and shampoo vac if available.
  5. Clean the lower door cards.

GYEON tip

Don't forget the undercarriage – salt hides where you can't see it.

Back to contents ↑
Real-life fix #

How to start spring cleaning right

Wash winter away – properly.

After a long winter, your car deserves a proper refresh. Snow, road salt and grime cling to the surface and, left untreated, cause damage over time.

In short

Spray Q²M Iron on the dry car, rinse, two-bucket wash with Q²M Bathe and the Q²M WashPad, then Q²M Tar on the lower panels with Q²M SilkMitt, rinse and dry with Q²M SilkDryer.

The background

Why Q²M Bathe for spring:
  • Removes heavy winter build-up like salt and grime without harsh chemicals – its pH-neutral formula is safe on all finishes, including nickel, chrome and polished surfaces.
  • Highly concentrated gel: a little goes a long way, with thick, long-lasting foam. Very slippery, reducing the risk of swirls and micro-scratches.
  • Safe for coatings and sealants.

Step by step

  1. Spray Q²M Iron generously on the dry, dirty car (wear gloves – it has a strong smell). When it turns purple, rinse.
  2. Wash with two buckets, Q²M Bathe in warm water and the Q²M WashPad, top to bottom; rinse the pad after each panel.
  3. Rinse thoroughly.
  4. Spray Q²M Tar heavily on the lower panels, let it work 2–3 minutes and agitate with Q²M SilkMitt.
  5. Rinse heavily.
  6. Dry from top to bottom with Q²M SilkDryer.

GYEON tip

Follow up with protection – see Get your car spring-ready with a proper coating.

Back to contents ↑
Real-life fix #

Get your car spring-ready with a proper coating

Spring means pollen, showers and grime. Time for a fresh layer of protection.

Spring brings unpredictable weather, pollen and road grime. The perfect time to give your car a fresh layer of protection that lasts.

In short

Wash thoroughly with Q²M Bathe, make sure the surface is clean, dry and cool, then seal it with Q² CanCoat EVO – sprayed onto a microfibre, wiped on and buffed to a gloss.

The background

Why Q² CanCoat EVO:
  • Effortless – spray on a microfibre, wipe on, buff.
  • Versatile – paint, trim, wheels, metal, carbon fibre, PPF and vinyl.
  • Durable – SiO₂ formula for long-lasting hydrophobicity, UV protection and a glossy finish that repels dirt.
  • Great value – one 200 ml bottle coats a car 10–15 times.

What you need

Clean microfibre towels

Step by step

  1. Wash thoroughly with Q²M Bathe.
  2. Make sure the surface is completely dry and cool to the touch; degrease with Q²M Prep.
  3. Work in small sections, away from wind and direct sun.
  4. Spray onto the microfibre – never directly on the car – and apply.
  5. Buff to a gloss.

GYEON tip

Do your wheels and trim in the same session – one bottle, whole car.

Back to contents ↑
Real-life fix #

5 things to watch out for in summer

Summer car care is as tricky as winter. Five things to keep in mind.

Summer car care can be as challenging as winter. Here are the five things to keep in mind.

In short

Wash cool panels in the shade, don't spray chemicals on hot surfaces, remove bugs quickly, don't keep products in a hot car, work in small sections and use a drying aid.

Step by step

  1. Heat: wash only when panels are cool, early morning or evening in the shade. Water evaporates faster on hot paint – more water spots. Don't spray cleaners on hot wheels right after a drive: they can etch.
  2. Bugs: in the heat, bug remains bake on and etch the clear coat. Wash more often if needed.
  3. Products in the car: some chemicals swell and leak in high temperatures – you don't want wheel cleaner all over your boot.
  4. One section at a time: work small areas so products don't dry. Sometimes wash and rinse one section before moving on.
  5. Drying aid: water evaporates faster in summer, so a drying aid adds lubrication – Q²M CeramicDetailer also adds some protection.

GYEON tip

Keep a quick detailer in your kit as a drying aid all summer.

Back to contents ↑
Real-life fix #

Summer or winter: does your car care need to change?

Summer and winter bring the most extreme conditions – and each needs its own approach.

Depending on where you live, you face very different weather through the year. Can you wash the same way in the heat and in the cold?

In short

In summer, work in the shade or early/late in the day on cool panels, and lubricate your drying towel with Q²M QuickDetailer. In winter, use warm water and Q²M WetCoat to shed water quickly, and have plenty of towels ready.

The background

Summer: products dry faster and can leave stains, water spots or even damage. Avoid cars that were just driven or baked in the sun.

Winter: cold water makes drying slow, and some cleaning products don't perform well in very cold water.

What you need

Q²M QuickDetailer drying aid in summer

Q²M WetCoat water shedding in winter

Q²M SilkDryer several towels

Step by step

Summer:
  1. Work in the shade, or early morning / early evening.
  2. Make sure panels are cool.
  3. Mist your drying towel with Q²M QuickDetailer as you dry each panel.
Winter:
  1. Use hot water where possible – it helps product performance.
  2. Use Q²M WetCoat after the wash so water beads off immediately.
  3. Have several drying towels ready.

GYEON tip

Whatever the season, never wash a hot car.

Back to contents ↑
Real-life fix #

Autumn is coming: coat your car and switch your shampoo

Autumn won't let you wash as often as you'd like. Prepare your car so it doesn't need it.

Autumn is here – and as usual, it will do its best to stop you caring for your car as often as you'd like. The perfect time to protect it for months.

In short

Coat everything with Q² CanCoat EVO – paint, trim, wheels, metal and side/rear glass. Then switch your shampoo to Q²M Bathe+, which adds hydrophobicity and self-cleaning with every wash.

The background

Q²M Bathe+ is not a typical 'wash and wax' shampoo: it leaves real hydrophobicity and self-cleaning ability, so your car stays cleaner for longer.

What you need

A foam cannon (optional)

Step by step

Coat:
  1. Wash the car and wipe with Q²M Prep to remove oils.
  2. Spray Q² CanCoat EVO onto the attached microfibre – not onto the car – and work in small sections.
  3. Apply in any motion and wipe until full gloss.
  4. Never in direct sunlight; keep it dry for 12 hours.
Wash with Q²M Bathe+ – three ways:
  1. Traditional: 20–30 ml in a bucket, wash, rinse.
  2. Quick: two pumps directly on the Q²M Smoothie, spread over the panel and rinse immediately.
  3. Foam: 30 ml in your foam cannon, spray, dwell 1–2 minutes, rinse thoroughly.

GYEON tip

Never let Bathe+ dry on the paint – rinse immediately, and don't use it in direct sun or on hot panels.

Back to contents ↑
Real-life fix #

How to prepare your car for storage

Put it away clean, dry and protected – and it comes out the same way.

Laying up your car for winter or a longer period? What you do before it goes into storage decides what you find when it comes out.

In short

Fix any moisture issues first, then clean or detail the car thoroughly – including the wheel arches and engine bay – so no dirt can trap moisture and cause corrosion.

The background

Damp fabric from a leaking sunroof or windscreen can turn into mould when the car sits still. Dirt attracts and locks in moisture, which can lead to corrosion.

What you need

Q²M Bathe wash

Q²M APC arches and engine bay

Q²M FabricCleaner interior

Q² Wax or Q² CanCoat EVO protection

Step by step

  1. Find and fix any leaks; make sure carpets and seats are completely dry.
  2. Wash and detail the car thoroughly.
  3. Clean inside the wheel arches and the engine bay – no dirt, grime or leaves.
  4. Clean the interior.
  5. Protect the paint before storage.

GYEON tip

Using a cover? Make sure both car and cover are completely clean first.

Back to contents ↑
Real-life fix #

Can a car cover damage your paint?

People use covers to protect their cars – and sometimes cause damage instead.

A frequently asked question. Many people think they're protecting their car with a cover – but they may be causing damage.

In short

Yes, if there is dirt on the car or inside the cover: putting the cover on drags that dirt over the paint. Used correctly, on a clean car with a clean cover, it protects.

The background

It also depends on where you store the car, and whether the paint is protected with a coating or PPF.

What you need

Q²M Bathe and Q²M SilkDryer clean car first

Q² CanCoat EVO or Q² Wax protection under the cover

Step by step

  1. Make sure the car is freshly cleaned.
  2. Make sure the inside of the cover is clean – lay it out and vacuum it if you have space.
  3. Never put a cover on alone – with two people you lift it over the car instead of dragging it across.

GYEON tip

A coated car is slicker – the cover glides instead of grabbing.

Back to contents ↑
Real-life fix #

Road trip car care: before, during and after

A little preparation before you leave makes the clean-up after much easier.

Road trips are as popular as ever. A little thought before you go makes the trip safer – and the clean-up afterwards much easier.

In short

Before you leave: clean the car, coat the glass with Q² QuickView and protect the front end. On the road: pack Q²M InteriorDetailer and Q²M Bug&Grime. Never 'quick detail' a dirty car.

What you need

Q² Wax or Q²M CeramicDetailer front-end protection

Q² QuickView glass

Q²M InteriorDetailer interior on the go

Q²M Bug&Grime bugs

Q²M WetCoat quick protection top-up

Step by step

Before:
  1. Clean the car thoroughly, especially wheels and tyres.
  2. Coat the windscreen and side glass with Q² QuickView for better visibility in bad weather.
  3. Protect the bonnet, front bumper and side skirts with Q² Wax or Q²M CeramicDetailer – fewer bugs and grime will bond.
On the road:
  1. Keep Q²M InteriorDetailer for eating on the move and refuelling stops.
  2. Avoid washing away from home. If you must, find a self-service wash where you can do a non-contact wash: Q²M Bug&Grime on bugs and heavy dirt, rinse, then Q²M WetCoat and rinse.

GYEON tip

Never 'clean' a dirty car with just a quick detailer and microfibre mid-trip – you will scratch the paint.

Back to contents ↑
Real-life fix #

How to clean your car after a track day

Track days leave heavy brake dust and rubber pick-up. Here's how to tackle it.

Track days mean more concentrated brake pad dust and tyre rubber pick-up than any road trip. Here's how to approach the clean-up.

In short

Wheels first with Q²M IronWheelCleaner and Q²M TireCleaner, protect with Q²M WetCoat, then do your normal pre-wash and wash and remove tyre rubber strikes with Q²M Tar.

What you need

Microfibre towels

Step by step

  1. Spray Q²M IronWheelCleaner liberally on the dry wheels, barrels and calipers.
  2. Spray Q²M TireCleaner on the sidewalls and agitate with a tyre brush.
  3. When the wheel cleaner turns purple, rinse. Inspect and repeat if needed.
  4. Wash the wheels with Q²M WheelMitt and shampoo, rinse, then spray Q²M WetCoat and rinse.
  5. Wheels off? Check the inner arches for rubber pick-up and spray Q²M Tar on it.
  6. Do your normal pre-wash and safe wash.
  7. Rubber strikes on the paint: apply Q²M Tar, let it dwell, then gently agitate with a microfibre soaked in Q²M Tar. Rinse.
  8. Protect the paint.

GYEON tip

The sooner you clean after the track day, the easier brake dust comes off.

Back to contents ↑
Real-life fix #

Selling your car? How to prepare the exterior

A little time and money spent on presentation can raise your car's resale value.

Investing a little time and money in preparing your car can improve its resale value. It's not about hiding anything – it's about presenting your car at its best.

In short

Make a plan, start with the wheels, clean the engine bay, wash and decontaminate the paint, add gloss, polish if needed, and finish with tailpipes, tyres and trim.

What you need

Q²M Iron and Q²M Tar decontamination

Q²M IronWheelCleaner wheels

Q²M Foam engine bay

Q²M WetCoat or Q²M QuickDetailer gloss

Q²M Clay Bar only if needed

Q²M MetalPolish tailpipes

Q² Tire or Q²M TireExpress tyres

Q²M Preserve plastic trim

Step by step

  1. Plan: identify the areas that could put buyers off.
  2. Wheels: clean wheels make all the difference.
  3. Engine bay: a dirty one suggests poor mechanical care. Light snow foam, brushes and a good rinse work wonders.
  4. Wash and decontaminate the bodywork; flush arches, door shuts and sills.
  5. Feel the paint with your palm. Rough? Clay only where necessary – it can leave light scratches.
  6. Gloss: Q²M WetCoat on the wet car, or Q²M QuickDetailer on the dry car.
  7. If you have time, polish by hand or machine.
  8. Tailpipes: Q²M MetalPolish removes carbon deposits.
  9. Dress the tyres with Q² Tire or Q²M TireExpress, and plastic trim with Q²M Preserve.

GYEON tip

Photos sell cars – shoot them right after you finish, in soft light.

Back to contents ↑
Real-life fix #

How to clean a motorcycle

So many exposed parts need a careful approach. Split the job in two.

With so many exposed components, a motorcycle needs caution from the outset. Split the job into two sections.

In short

Lower section (wheels, drivetrain, suspension, engine): Q²M Bug&Grime and brushes. Upper section (seat, tank, fairing, screen/visor): a gentle wash with Q²M Bathe.

The background

Why Bug&Grime instead of APC on the lower part? If you get an APC dilution wrong it's either too aggressive or too weak – Bug & Grime is ready to use.

What you need

Engine bay brushes

A wash mitt and bucket

Step by step

  1. Run the bike for a few minutes – just warm, never hot – to loosen grease.
  2. On the dry bike, soak the lower section with Q²M Bug&Grime and let it dwell.
  3. Rinse, re-apply and agitate the components with engine bay brushes. Rinse and repeat if needed.
  4. Upper section: rinse, then wash with Q²M Bathe and a mitt, as you would your car's paint. Take care around instruments and navigation screens.

GYEON tip

Protect the tank and fairing with Q²M WetCoat after washing – the next clean is much easier.

Back to contents ↑
Knowledge #

How to clean your engine bay safely

The least cleaned area of most cars – because people are afraid. With a few precautions, it's easy.

Possibly the least cleaned area of your car – mostly out of fear of damaging something. With a few simple precautions, cleaning a modern engine bay is safe.

In short

On a cool engine, blow off loose debris, cover open air filters, the alternator and exposed electrics, clean top to bottom with Q²M APC and brushes, rinse gently and dry with air.

What you need

Q²M APC 1:5, up to 1:1 for heavy dirt

Q²M Bathe+ quick protection

Long wheel brush and detail brushes

Old microfibres or a dedicated mitt

Plastic bags

A water-based plastic dressing

An air blower or compressed air

Step by step

  1. Make sure the engine is cool. Older or performance cars: protect all exposed sensitive components.
  2. Blow off leaves and loose debris while dry.
  3. Cover open air filters, an exposed alternator and electrical areas with plastic bags.
  4. Start under the bonnet: spray Q²M APC on the exposed metal and agitate with a brush. Don't soak the sound-deadening mat – it can collapse under the weight of water.
  5. Lightly wet the engine bay (pressure washer at 1.5–2 m), spray Q²M APC, let it dwell 3–4 minutes and agitate with brushes and a mitt.
  6. Rinse carefully. Inspect and repeat if needed.
  7. Apply a water-based plastic dressing while still wet, brush it in, leave 4–5 minutes and wipe off the excess – or foam the bay with Q²M Bathe+ for quick protection.
  8. Blow water out of connectors and moving parts with air.

GYEON tip

Long wheel brushes are perfect for getting safely between engine components.

Back to contents ↑
Knowledge #

When to use a steam cleaner on your car

A steamer is one of the most versatile tools in a detailer's kit. Here's where it shines.

A steam cleaner is a versatile, integral tool in a detailer's kit. Combined with the GYEON maintenance range, it can tackle almost anything your car throws at you.

In short

Use a steamer on interior stains (with Q²M FabricCleaner), in engine bays (no blasting water at electrics) and in wheel arches (with Q²M APC).

The background

  • Interior: steam plus Q²M FabricCleaner lifts stains and ground-in dirt – safer than heavy scrubbing that damages fibres.
  • Engine bay: reach tight areas without soaking delicate electrical parts.
  • Wheel arches: they take a beating – steam with Q²M APC is the perfect combo for heavy grime.

What you need

Q²M FabricCleaner interior

Q²M APC engine bay and arches

A steam cleaner

Microfibre towels

Step by step

  1. Pre-treat the area with the matching GYEON cleaner.
  2. Steam to loosen the dirt.
  3. Wipe away immediately with a clean microfibre.

GYEON tip

Never use steam on leather – heat can change its shape and fit.

Back to contents ↑

Product index

Every GYEON product mentioned in this book, with links to the guides where it is used.

Q² Skin EVO

1 related guide

Q²M APT EVO

1 related guide

Q²M SilkDryer Ultra EVO

1 related guide

Guides A–Z

109 guides. One way of caring.

From choosing your first shampoo to coating your wheels, reviving PPF or saving a leather seat from a spilled coffee – The GYEON Car Care Book explains what to do, which products to use and how to get a professional result at home.

In G we trust · GYEON

Back to top ↑