Adam's Graphene Shampoo 16oz — wash away road film with rich lubrication and easy-rinsing suds.
Adam's Graphene Shampoo 16oz
Revitalize And Maintain Your Coating.
Graphene Shampoo™ is a versatile solution combining a foaming degreaser and shampoo that will aid in the removal of stubborn contaminants without harming your existing coating, sealant or wax! This variation on a traditional foaming shampoo balances choice, high foaming surfactants, and citrus-based degreasers to generate a wash that is more than capable of powering through all kinds of road films and grime with ease!
- Contains Graphene Ceramic Resins
- Helps Maintain & Revitalize Graphene and Ceramic Coatings
- Highly Concentrated, Low Viscosity, Free Rinsing Formula
- More Easily Removes Road Films & Grime
- Smoke Color and Fresh, Clean, Citrus Scent
Graphene Shampoo™ is also the shampoo recommended to work best to revitalize and maintain the coatings generated by products like Graphene Ceramic Coating™ or Graphene Ceramic Spray Coating™ once applied. Graphene Shampoo™ helps to decontaminate the coatings by removing harmful contaminants that would sap the coating’s durability and interfere with the hydrophobic, self-cleaning effects.
Instructions for Use with Foam Cannon, Foam Gun, or Pump Sprayer:
- Add a small quantity of water to your foam cannon, foam gun, or pump sprayer and dispense 2-3 fl oz of Graphene Shampoo™ to the reservoir. Top up with water to volume and tilt/agitate the to fully dissolve the shampoo.
- Adjust fan pattern and soap to water ratio for desired concentration and connect to dispenser.
- Foam down vehicle from top to bottom and allow the shampoo to wet out over the entire vehicle and penetrate grime.
- Utilize a wash pad, mitt, or sponge to agitate off any stubborn contaminants and road films.
- Rinse off thoroughly using pressurized water until no evidence of bubbles or foam persists.
- Dry the vehicle utilizing a combination of a drying aid, pressurized air, and/or drying towels, in order to avoid any potential water spotting.
Instructions for Two Bucket Wash Method:
- Start by adding a grit guard to each of the rinse bucket and wash bucket, along with adding any of a wash pad, mitt, or sponge and 2-3 fl oz of Graphene Shampoo™ to the wash bucket specifically. Now add approximately 3 gallons of water to fill each bucket.
- Working from the top of the vehicle down to bottom, in small sections, wash the vehicle and periodically dunk the wash pad, mitt, or sponge in the rinse bucket before dunking it back into your wash bucket to get fresh suds. This helps keep contaminants that could scratch the paintwork trapped in the rinse bucket rather than infiltrating into the wash bucket. Repeat this process for the entire vehicle.
- Rinse off the vehicle thoroughly until no evidence of bubbles or foam persists.
- Dry the vehicle utilizing a combination of a drying aid, pressurized air, and/or drying towels, in order to avoid any potential water spotting.
Common Sense Warning:
Always apply soaps, including Graphene Shampoo™, on cool surfaces, trying to avoid allowing the soap to dry on the surface and, when able, not using in direct sunlight.
How to use
- Work on cool panels in shade. Rinse loose grit from the vehicle and prepare a clean wash mitt and separate rinse bucket.
- Measure the shampoo for your bucket or foaming equipment using the directions for this formula. Foam output varies with dilution, water hardness and equipment.
- Wash from the upper panels downward with light pressure. Rinse the mitt frequently and use separate tools for wheels and lower grime-heavy areas.
- Rinse thoroughly before the shampoo dries, including mirrors, seams and trim. Dry with a clean microfiber drying towel or a suitable vehicle dryer.
Aftercare and maintenance
Rinse wash mitts and buckets after use and allow them to dry. Flush foam equipment with clean water so dried shampoo cannot clog its internals. Maintain paint protection as needed and remove bird droppings or road contamination promptly.
Does more foam mean the paint is clean?
Foam helps distribute shampoo and loosen contamination, but it does not establish that all dirt has been removed. Inspect the finish and use a careful contact wash when needed. Never let foam dry while waiting for it to do more work.
Complete your detailing routine
Choose compatible products for the next step of your detail:
