For the Next Wash: A Subaru Impreza STI Detail with GYEON

CARZILLA JOURNAL · GYEON DETAILING NOTES

Blue paint. Grey wheels. A little forward planning.

An afternoon with the smaller details, and a thought for whoever has to clean those spokes next time.

4-minute read · Subaru Impreza STI · Photos by GYEON

Blue bodywork, a bonnet scoop and a set of grey wheels: this Subaru Impreza STI doesn’t need much introduction. The workshop lights in these photos make the paint look almost electric. But after admiring that first shot, I keep coming back to the wheels. There are quite a few spokes here. Sooner or later, someone has to clean around every one of them.

That’s where I’d put my time if this STI were in the garage for an afternoon. The wash would be finished, the car cool and dry, and the focus would shift to protection. A few GYEON coating boxes are lined up in the photos, but I’d keep this particular session centred on two jobs: the wheels and compatible exterior trim.

Thinking about the wash after this one

I like the idea of doing a little extra work now to make the next clean less of a chore. GYEON Q² Rim EVO is a ceramic wheel coating that helps reduce the adhesion of brake dust and road contamination. The wheels will still get dirty. The useful part is helping that dirt release when it’s time to wash again.

Before opening the bottle, I’d make sure the wheel finish is suitable and test a discreet area, especially if preserving its exact colour matters. Rim EVO can enrich or darken a finish. On these grey wheels, I’d want to retain their character and let the shape of the spokes do the talking.

Gloved hands holding GYEON Rim EVO packaging beside a Subaru STI alloy wheel
Rim EVO beside the STI’s multi-spoke wheel: plenty of small areas to work through carefully.
GYEON Q² Rim EVO bottle beside the spokes of a Subaru alloy wheel
A closer look at the wheel finish, with GYEON Q² Rim EVO ready for a prepared surface.

One wheel, then the next

The preparation would get most of my patience. Brake dust, tar and old protection need dealing with before coating, using methods suited to the finish. Then everything needs to be completely dry, including the little pockets around the wheel bolts. A wheel can look ready from a few steps away while still holding moisture in exactly the places you’re about to touch.

I’d degrease as directed and observe the preparation product’s waiting time, then work through small, accessible sections with the applicator. On a wheel like this, I’d give myself a simple route around the spokes so I can keep track. Apply evenly, level and wipe within the coating manual’s short working window, then inspect from another angle. A little change in position can reveal residue that was invisible a moment earlier.

There’s no need to turn this into a speed exercise. I’d keep the coating on the intended wheel surfaces and away from tyre tread and brake friction surfaces. If I couldn’t comfortably reach an area, I’d plan proper access instead of trying to coat it by feel. A tidy, controlled application appeals to me far more than claiming every hidden corner was done.

The next wash is part of the plan, even while this one is still fresh.

A little attention around the blue

With the wheels finished, I’d move to the smaller exterior details. The Trim EVO photo draws your eye to a dark vent against the blue paint. It’s a good reminder to identify the material first: mesh, painted pieces and plastic trim can sit right beside each other, and they don’t automatically need the same treatment.

GYEON Q² Trim EVO and an applicator beside a dark vent on blue Subaru bodywork
Trim EVO and an applicator beside the blue bodywork. Check each material before deciding where to apply a coating.

For suitable plastic trim, GYEON Q² Trim EVO is an option for protection and colour enrichment while keeping a natural matte or satin character. I’d test first, clean away any old dressing, let the surface dry fully and follow its preparation and application instructions. The small borders are where I’d slow down again, checking for accidental transfer onto neighbouring paint.

Both coatings need to stay dry for at least the first 12 hours. I’d leave the Subaru sheltered and follow each coating’s manual for the rest of the cure. Those grey spokes can wait until the next wash.

The product links in this story take you to the matching GYEON products at CARZILLA.

Photography supplied by GYEON. A detailing story inspired by the Subaru Impreza STI photo series.