Keeping That Fresh PPF Feeling on a Matte Audi RS5
CARZILLA JOURNAL · GYEON PPF
Good film. More miles.
A matte RS5, a road worth taking and the care that keeps its finish looking right.
Approx. 9-minute read · GYEON × WRAPSIGN photo story
There’s a photograph in this set that makes us want to put the wash bucket away and find a road with a few bends. A grey Audi RS5, black wheels, red brake calipers and that lovely soft finish across the bonnet. We could spend a while looking at it parked. We’d still rather see it leave the car park.
This is the GYEON × WRAPSIGN project, an RS5 transformed from gloss to matte with paint protection film. The installation photographs are fascinating, but our thoughts keep wandering past the reveal. Once a car looks this good, how do we keep enjoying it without turning every dusty drive into a detailing emergency?
At CARZILLA, our answer starts with a manageable routine. Give the film time to settle, wash it gently, and choose products that suit the finish. GYEON PPF Wash, PPF Maintain REDEFINED and PPF EVO each have a place in that routine. Looking through these photos, here’s how we’d put that care into practice.
The light is doing something different now
Under the workshop lights, the RS5’s bonnet has a broad, soft highlight. Outside, the grey changes again. The front wings pick up the sky, the grille stays dark, and the red calipers suddenly look very bright. We like how the matte surface lets the body shape hold our attention. Even a familiar car starts to look a little unfamiliar.
That’s a big part of the appeal of GYEON PPF Matte. It changes the way light sits on the existing colour while adding a protective film over the covered paint. For anyone who likes their car’s colour but wants a softer finish, this RS5 makes a convincing case.
GYEON’s PPF range also includes glossy films with water-repellent and self-healing surface properties. The exact behaviour depends on the film. Self-healing can help with light surface marring, while the film itself provides a physical barrier against some everyday chips and scuffs. Deep cuts and serious impacts still have consequences. We’d choose coverage with the installer around how the car actually gets driven.

Those careful edges deserve a careful first wash
Go back a few photographs and the RS5 is raised in the bay, its bonnet open and wheels covered. There’s a lot happening around the front corners. A headlight, a grille opening, a curved wing and a panel gap all meet within a small space. Seeing someone work there makes us appreciate how much fitting goes into the finished car.
We’d carry that thought home. Before reaching for shampoo, get the installer’s aftercare instructions and confirm when washing and coating can begin. GYEON’s published film guidance allows 48–72 hours for settling and says to avoid chemical washing for the first 14 days. The specific installation, weather and any coating applied alongside it need to be part of that conversation.
Those early days are a good time to leave the edges alone. If something looks lifted or unusual, send the installer a clear photo. Picking at an edge or trying to press it back with whatever is in the garage can turn a small concern into extra work. We’d rather have the person who fitted it take a look.

How we wash matte PPF
Once the film is ready for maintenance, we’d let the RS5 cool in the shade before starting. The low front end is exactly where we’d expect bugs and road grime after a drive. The lower doors would get a closer look too. A gentle rinse helps show what is loose and what needs more time to soften.
With a pressure washer, keep a sensible distance, use a broad spray and follow the installer’s guidance for the equipment. Avoid aiming a concentrated jet into film edges and seams. Around a stubborn patch, our first move would be more soaking time with an approved cleaner. Holding the nozzle closer is a tempting shortcut with very little appeal once you’ve watched the installation work.
For straightforward maintenance washes, GYEON Q²M Bathe gives us a lubricated, pH-neutral shampoo. Use the bottle’s dilution, clean wash media and light passes, working from cleaner upper panels towards the dirtier lower areas. Wheel brushes and wheel mitts stay with the wheels. The black wheels look great here, but their dirt doesn’t belong in a mitt travelling across the bonnet.
We’d rinse the mitt frequently or swap to clean wash media as we go, then rinse each section before the shampoo can dry. PPF still rewards a light hand. The aim is to carry dirt away while keeping that soft, even finish intact.
Where GYEON PPF Wash earns its place
A car can look reasonably clean from a few steps away and still have contamination sitting on its film. This is where GYEON Q²M PPF Wash becomes useful. It’s a decontamination shampoo formulated for film and vinyl, with the ability to tackle mild iron deposits as part of the wash.
For the bucket method, GYEON specifies a 1:500 dilution. That works out to about 20 ml in 10 litres of water. We’d measure it, use clean wash media and rinse thoroughly, keeping the surface cool throughout. The formulation is coating safe and can be used on compatible painted areas too, which makes life easier on a car with partial PPF coverage.
We’d build PPF Wash into the care routine alongside regular washing. GYEON recommends PPF Wash and PPF Maintain at least monthly for its film. Mileage, storage and exposure still matter, so a car that spends its week outside may need attention sooner. A quiet weekend car has a different life from something commuting through wet road spray every day.
Its ability to remove mild iron contamination is useful, but a stubborn tar spot or an unidentified stain deserves its own assessment. We wouldn’t automatically reach for clay or scrub harder on matte PPF. Start with the film manufacturer’s approved approach, test carefully and ask the installer when a mark won’t respond.

The last water is usually hiding somewhere
On this Audi, we’d be watching the mirrors, grille openings and gaps around the rear hatch after rinsing. There’s always one little reservoir waiting until the towels have been put away. A gentle flow of air can help coax water out, followed by a clean microfibre drying towel to take up what remains.
Use light contact and change to a dry towel when the first one stops absorbing well. We like working one section at a time because it gives us a chance to notice a missed patch or fresh drip. Leaving the car to air-dry can leave mineral marks, including on film that beads water beautifully.
That final walk around also tells us whether anything else is needed. If the film looks even and feels clean, we’re already in a good place. We don’t need to make every wash an afternoon of extra treatments just because there are bottles on the shelf.

PPF Maintain is our easy finishing step
When we want to refresh slickness and water repellency after washing, GYEON Q²M PPF Maintain REDEFINED fits neatly into the job. It’s a silica-based maintenance spray for PPF and vinyl, suitable for glossy and matte film. It can also be used to maintain film protected with PPF EVO.
On this matte RS5, we’d start with clean, dry film and a small test area. Put a little product on a suitable clean microfibre or apply as directed, spread it evenly and use a fresh towel face to finish. Small sections make it easier to see what’s happening. More spray means more residue to manage, especially around badges and panel gaps.
Then step back and look along the panel. What we want is the same consistent appearance that drew us to the car in the first place. If there’s a streak, deal with it before moving on. A light, controlled application is much more satisfying than circling the whole car again to chase excess product.
PPF Maintain suits owners who enjoy a simple finishing step after the wash. You can use it on suitable uncoated film too. There’s no need to buy a ceramic coating first just to make the maintenance spray useful.
When we’d choose GYEON PPF EVO
If we were planning longer-term protection for this car’s film, we’d consider GYEON Q² PPF EVO. It’s a dedicated ceramic coating for PPF and compatible vinyl. It adds water repellency and helps the surface resist contamination, making subsequent cleaning easier. The film provides the physical protection beneath it.
GYEON lists PPF EVO for gloss, satin and matte film without adding gloss. That matters on this RS5. We’d check compatibility with the installed film and its existing topcoat, then test a discreet area. The coating is designed around film’s flexibility and normal self-healing behaviour, so it makes sense as a deliberate part of the care plan.
This is a job we’d set aside proper time for. The film needs to be clean, decontaminated where necessary and thoroughly dry, including around seams. Follow GYEON’s preparation instructions and the installer’s timing for new film. Work in manageable sections, level the coating promptly as directed and inspect the surface from more than one angle.
The initial cure needs planning as well. Keep the coated surface dry for at least 12 hours, and follow the supplied manual for the remaining cure and first wash. An evening application followed by overnight dew is easy to overlook. The film’s installation waiting period and the coating’s cure are separate requirements.
PPF EVO is rated for up to 24 months or 25,000 km, with preparation, use and maintenance affecting the result. We’d still wash regularly and use PPF Maintain as appropriate. If water behaviour changes, clean and inspect the film before deciding the coating needs replacing. Dirt can hide the performance of the surface underneath.

Keeping matte PPF matte
The bonnet in these photographs is a useful reminder of what we’re preserving. That soft reflection is the whole point. A shiny patch from an unsuitable polish would draw our eye immediately, even if the rest of the car looked spotless.
We’d keep abrasive compounds and conventional polishing routines away from matte film. GYEON PPF Renew, for example, is a light abrasive maintenance product intended for glossy PPF. It doesn’t belong in this matte care routine. Sharing a brand name doesn’t make every product interchangeable, and a test spot matters whenever a finish is unfamiliar.
Between washes, deal with bird droppings and insects promptly using a film-approved method. Soften contamination before gently removing it, avoiding a dry wipe through grit. During the initial settling period, ask the installer how they want contamination handled. If there’s persistent staining, damage or lifting, that’s a reason to get their advice.
We’d still take the longer road
The best frame to finish on is the RS5 outside the studio. All that careful fitting now has a purpose. There are roads to drive, places to park and another wash waiting somewhere down the line. We like PPF most when it makes an owner more comfortable enjoying their car.
Our routine for a finish like this would be easy to remember. Gentle regular washing, PPF Wash for film-focused cleaning, PPF Maintain when it’s time to refresh the surface, and PPF EVO if we want a dedicated ceramic coating. Each earns its place through the job it does.
After that, we’d put the clean towels away, have one more look at the grey against those red calipers, and leave the driveway. A matte RS5 deserves to be seen somewhere other than under workshop lights.

Photography from the GYEON × WRAPSIGN series. PPF care notes from us at CARZILLA.