Five Spokes First, Then the BBS Mesh

CARZILLA FIELD NOTES   /   7 MIN READ

If we were picking wheels for the drive home, the bronze BBS set would start an argument around here. Bronze against that green fender, a yellow centre cap and just enough bright metal around the edge to catch your eye from across the street. We can picture those in our driveway a little too easily. Hand us a bottle of wheel coating and ask which set we want to do first, though, and we’ll take the silver Porsche five-spokes.

You can probably guess why from the first photo. There’s a gloved hand beside the Porsche crest, a little blue pad and a whole lot of room on either side of it. We can see where we’d put the pad down and where we’d lift it off. Over on the BBS, the same pad looks big enough to cover three different decisions. That’s what we like about these two sets of photos. Same bottle of GYEON Q² Rim EVO, two good-looking sets of wheels, and one good reason to count the spokes before you promise to be done by lunch.

Five spokes give us room to get our eye in

Take a look at the opening just above the Porsche badge. The spoke rolls away from the light so gently that the silver changes from almost white to grey before it disappears around the back. Run a towel straight across the face and you’ll get the bright bit. To reach that little grey shoulder, you’ve got to turn your wrist. A wheel with this much open space makes it easy to see exactly where that turn happens.

Before the blue pad comes out, we want the wheel cool, washed and free of brake dust, old protection and oily residue. The bits that are easy to miss on this design are the little recesses around the lug hardware. Water can sit in there long after the broad silver face looks dry. We’d rather find a stray drop with a clean towel now than watch it run down a spoke we’ve just coated. Once the wheel is properly clean and dry, our final wipe is with GYEON Q²M Prep. GYEON calls for a 15-minute wait after Prep before applying Rim EVO.

That leaves us time to do something faintly ridiculous but genuinely helpful. Pick a spoke and try the whole movement with a clean, dry towel. Can we follow that curved shoulder with two fingers underneath the fold? Can we reach back out without the loose end brushing the next spoke? On this Porsche the answer comes pretty easily. It’s worth knowing before there’s coating on the wheel and a clock ticking in our head.

A bead of GYEON Rim EVO falls onto a blue applicator held in front of the silver wheel.
A dark line on the blue fabric shows where the coating has landed. We like having our first spoke picked out before this point.

There’s a second half to every pass

The applicator photo catches a drop in mid-air and a dark stripe developing along the blue fabric. What’s outside the frame matters just as much to us. We want a clean levelling towel folded into quarters and close enough to grab with our free hand. If it’s still in a bag three steps away, now’s a fine time to go get it.

On the Porsche we’d start beside the centre cap, work outward along one broad spoke, then follow its shoulder into the opening as far as we can comfortably wipe. The towel takes the same trip while we still remember it. GYEON’s current wipe-off window for Rim EVO is short, about 10 to 30 seconds after application. That’s why we think in spokes here. We can spread and level one small section at a comfortable pace. Coating all five faces before reaching for the towel would give the first one quite a head start.

Here’s the part that can fool us on silver. A straight-on view makes almost everything look even. Move your head until the strip of light slides across the spoke and a smear near the edge becomes much easier to spot. With a fresh towel face we can catch that spot as we go. Once we’ve got the first spoke right, there are four reassuringly familiar shapes left. We might even start thinking we’re quick at this. Then there’s the BBS.

A bronze BBS mesh wheel with a bright outer lip under a green fender, with the Rim EVO box held beside its spokes.
Look past the box to the outside of the wheel. Every bronze spoke meets a narrow ledge just inside that bright lip.

Bronze mesh has other plans

Look at the outside of that bronze face, just inside the silver lip. There’s a row of little fasteners, and behind them a run of narrow openings with corners that come almost to a point. Follow one spoke in towards the yellow cap and it joins its neighbour. We love the way the pattern changes as you trace it. It’s also how you can lose your place while looking directly at the thing you’re working on.

For this wheel we’d use the valve stem as our starting mark and finish one opening at a time. Take the two bronze edges that frame it, turn the pad to reach the sides we can see, and level them before moving round. The wide face of the pad can ride along a spoke, but it won’t fit into the point of every little triangle. A clean fold of towel gives us a narrower edge for wipe-off. If we can’t get that towel back into a particular spot, we leave the applicator out of it too.

A detailer holds a blue applicator at the bronze spokes just below a yellow BBS centre cap.
The yellow BBS centre cap gives us a landmark. We can follow a spoke out towards the lip and see exactly which opening to tackle next.

The bright outer lip deserves its own pass. The bronze spokes break up reflections into lots of little pieces, while the lip gives us one continuous strip to look along. A smudge shows up differently on each. We like to sight along the rim from the side, turning a clean towel face as we go. Keeping the job to the accessible wheel face also means the blue pad stays well away from the brake disc visible through the openings. We’re concentrating on the faces of wheels that are still on the cars. A job that includes the whole inner barrel calls for access right around the back of the wheel.

The droplet we’d look for first

Our favourite BBS close-up has a few water droplets sitting on that bright lip. Magnify it and you can see how close the little fasteners sit to the bottoms of the spokes. If a wheel looked like this just as we were about to start coating, the cap would go straight back on the bottle. One small drop tucked in a recess can come out the instant a towel passes over it. It’s a good argument for putting the work light down low and giving the whole rim another look before starting on beautiful, complicated wheels.

Water droplets along the bright outer lip of the bronze BBS wheel, with a Rim EVO bottle between the spokes.
From this low angle you can see the outer lip, the line of exposed hardware and the tiny corners where the spokes end.

It’s tempting to reach for the hose after coating a wheel, especially one that photographs this well. We save the water for a later wash and keep fresh Rim EVO dry for at least the first 12 hours, following the kit instructions for curing and aftercare. The bit we actually look forward to comes when that bronze mesh has picked up a normal week’s worth of brake dust. The brakes will still make dust. The point of ceramic coating wheels is to make that dust easier to release the next time we wash them. On a wheel with this many corners, we’ll take all the help we can get.

Give us the first set to coat on a quiet afternoon and we’re still picking the Porsche. We like being able to follow the light across a whole spoke in one go. But ask us the same question when both cars are parked outside, the towels are in the wash and that bronze is catching the last bit of daylight against the green fender. We’re pretty sure someone at CARZILLA is going to change their vote.